Your shower drain can connect to the toilet drain, but it cannot connect to the toilet trap arm. So if your “main drain connection” is also the vent for the toilet, the line from the closet flange to the main drain connection is trap arm and the answer is no, the shower cannot tie in here.

Also, Can two toilets share same stack?

Most houses have more than one toilet, and if they are on the same side of the house, their waste lines can usually tie into the same stack. If they are on opposite sides, however, each may need its own stack. Since the stacks must be vented, this would mean two vent openings on the roof.

In this way, Can a toilet be moved 6 inches? There is no easy way to move it, but moving it 4″-6” is often easier than moving it 1″ or 2″. Also, unless that bathroom does not have any walls around it the water heater is not permitted in the bathroom.


20 Related Questions Answers Found

 

How do you tighten a toilet seat with no access to the underside?

The procedures to tighten the toilet seat
  1. Step 1: Exam the toilet closely one again. For the majority of the cases, your toilet probably did have holes for underside access.
  2. Step 2: Re – align the seat.
  3. Step 3: Tighten the bolts.
  4. Step 4: Check the tension and close the lid.

How can I hide my toilet waste pipe?

How to Hide Plumbing Pipes in your Bathroom
  1. Bathroom furniture. Bathroom furniture such as vanity units and cistern units, provide a simple yet effective way to hide the plumbing pipes in your bathroom.
  2. Choose a pedestal basin.
  3. Conceal pipes in the wall.
  4. Fit a wall hung toilet.
  5. Build a fake wall.

What is a bottom fix toilet seat?

Bottom fixing toilet seat hinges feature a traditional style fixing which includes fitting two bolts down into your pan and then tightening them from underneath. Wing bolts are often used. If you can get your hand up behind the toilet and feel the bolt, it is likely that a bottom fix toilet seat is the seat you need.

How do soft close toilet seats work?

A slow close toilet seat is basically one that closes on its own as soon as you start to push it down. Gravity controls it but special, tensioned hinges control the gravity. Designed with special toilet seat hinges, these seats lower very slowly and make virtually no sound when they come to their closed position.

Can you connect sink waste to toilet waste?

Without the upper vent portion of the pipe, water locks can form in the drain system. The sink vent serves both the sink and the toilet. The configuration depends upon your bathroom layout and the direction of the floor joists, but connect the sink drain to the toilet drain within 6 feet of the toilet, if possible.

How do you replace a hidden bolt on a toilet seat?

After removing the caps, you can now see the top side of the bolt that is holding the seat in place. Under the toilet, you will find bolts that stick out. These bolts are tightened by wingnuts. Use the pliers to keep the nuts steady and then use your screwdriver to unscrew the bolt.

Can toilet waste pipe run under floor?

Soil pipes are generally located on an outside wall and enter the bathroom as close as possible to the toilet location. They can be mounted on the floor, but usually pipes run below the floor in-between the floor joists. Running this pipe from one end of the house to the other simply is not practical.

Can you connect shower waste to soil pipe?

Should I caulk around my toilet?

Turns out, caulking your toilet to the floor is actually smart. These clients say that caulking around the base of the toilet would trap water from a leaking toilet, causing damage below and around the toilet since it has no place to leak onto the floor.

How tight should the toilet bolts be?

The toilet bolts should not be overtightened, but they should be tight. If you hear the sound of metal on porcelain, stop tightening. But if you still feel the bolts tightening against the wax ring, keep going.

Can a plumbing vent have bends?

Plumbing vents need to be straight on the vertical. Plumbing vent pipes are used to allow fresh air into the plumbing system and help the other drains in the house work properly. This means that there are bends or connections in the other piping and this piping needs to attach to the venting system.

How do you fix a rocking toilet?

To steady a rocking toilet, cut plastic shims to fit and slip them underneath (you may have to remove caulk before adding shims). Then caulk around the toilet and snug down the nuts on the bolts. But don’t crank them down super-tight; that can crack the toilet.

How many toilets can be on a 3 inch drain?

1 Answer. Referring to the International Plumbing Code, a bathroom group requires 5 Drainage Fixture Units. As a horizontal branch 3” is good for 20 DFU’s or 4 bathroom groups.

How much does it cost to fix a wobbly toilet?

On average, it will cost from $45 to $197 to fix a toilet yourself or between $130 and $310 to have professional repairs done by a plumber.

How deep are storm drains buried?

First of all, the shape and dimensions of the seat should correspond to the dimensions of your toilet. You also need to choose the colour, which is a key design element for your bathroom. The many Villeroy & Boch collections allow you to express your style, from the bath to the furniture through to the toilet seat.

How deep are storm drains buried?

What is the proper slope for a drain pipe?

According to plumbing code, drain pipe has to be sloped a minimum of 1/4-inch per foot and a maximum of three inches per foot or vertical. A slope of less than 1/4-inch per foot will cause constant drain clogs and a slope of more than three inches will allow the water to drain without the solids.

Can you adjust a soft close toilet seat?

A toilet seat should be aligned with the bowl. While the lowering action on most softclose seats cannot be adjusted, it’s easy to make minor adjustments to the seat hinges if they become loose and the seat comes out of alignment or starts to slide around on top of the bowl.

How do you tighten a Villeroy and Boch toilet seat?

Flexible toilet seat assembly
  1. Simply click the Vario-nuts into place in the attachment screws.
  2. Screw the seat hinges from above into the toilet attachment.
  3. Attach the seat.
  4. Adjust the position of the seat precisely and tighten the screws.

Can a drain pipe have too much slope?

Improper drain slope

The ideal slope of any drain line is ¼ inch per foot of pipe. In other words, for every foot the pipe travels horizontally, it should be dropping ¼ inch vertically. Many drains either have too little slope or too much slope. That’s right, it is possible to have too much slope in your drain lines.

A 110mm foul drain taking the discharge of less than 1 l/s should be laid at a 1:40 (25mm per metre) fall. A foul drain taking the discharge from a minimum of one WC can be laid at 1:80 (12.5mm per metre). Gullies incorporating in foul water or combined drainage systems must have a 50mm minimum water seal.

Does a washing machine drain into sewer?

Washing machine drains are fed by an electric pump, which moves water from inside the cleaning drum, through a flexible drain hose on the underside of the machine, and out into your home sewer system where it makes its way out of the house.

How tight should tub drain be?

Once the flange is carefully threaded into the first few threads of the drain elbow, use the Smart Dumbell to hand-tighten the flange into the drain elbow until tight. Then use your wrench to tighten, by one quarter of a turn. Do this carefully, so as not to squeeze the gasket underneath the tub out of place.

How tight should tub drain be?

Properly backfilled, corrugated plastic pipe can be buried at depths of 20 ft (6 m) or more.

How do I vent my bathroom plumbing?

Vanity Venting

In new construction, the simplest way to vent a bathroom group is usually to install a single vertical vent pipe behind the bathroom sink. This works as long as all the plumbing fixtures connect to the main drain line in the floor within 6 to 10 lineal feet of the sink drain.

Can sewer vent run horizontal?

To answer your specific question, yes, vent pipes can have horizontal runs, as long as there is no possibility of them becoming plugged with water. In other words, any water that gets into the vent pipe opening must be able to run freely all the way to the sewer, without creating a “trap”.

How do I change the bolts on a toilet seat hinge?

Standard metal hinge with residential Sta-Tite®
  1. Thread the bolt into the hinge.
  2. Push the bushing all the way up bolt until it’s flush with the hinge.
  3. Place toilet seat bolts into toilet bowl.
  4. Finger-tighten Sta-Tite® nut onto bolts.
  5. Align toilet seat onto bowl and use a 1/2″ wrench to tight bolt.

How do you secure a toilet to the floor?

Toilets should be caulked to the floor to prevent side-to-side movement that can break the wax seal (and to prevent splashes or overflows from puddling under the toilet and rotting the floor). DIYers often set the toilet and then apply a tiny bead of caulk along the outside edge.

What is the minimum fall for sewage pipes?

To answer your specific question, yes, vent pipes can have horizontal runs, as long as there is no possibility of them becoming plugged with water. In other words, any water that gets into the vent pipe opening must be able to run freely all the way to the sewer, without creating a “trap”.

A 110mm foul drain taking the discharge of less than 1 l/s should be laid at a 1:40 (25mm per metre) fall. A foul drain taking the discharge from a minimum of one WC can be laid at 1:80 (12.5mm per metre). Gullies incorporating in foul water or combined drainage systems must have a 50mm minimum water seal.