How To Install Quarter Round Molding Without A Nail Gun. Instead of hammering your finishing nails all the way into the molding, which would result in an ugly, hammer-shaped dent, you‘re going to hammer them almost all the way in, then finish the job with the nail set.

Simply so, How do you nail in quarter round trim?

Position a 1-1/4-inch finishing nail at the middle of the molding two inches from the end. Hold the nail so it is nearly perpendicular to the floor. Hammer the nail through the quarterround and into the baseboard with a hammer.

How do I fasten quarter round? 1. Make your first cut at a 45-degree angle using your miter box and saw, then make your measurement for the total length. If you are adding quarterround molding to a four-cornered room, then all your cuts will be at a 45-degree angle with the angles running towards the center of the piece of molding.


33 Related Questions Answers Found

 

Can I use brad nails for quarter round?

The brad nailer is definitely the one to use for attaching quarter round to your baseboard. The combination of the 2 guns is great. The BN200A will shoot from 3/4″ to a 2″ brad, so you could use it to attach light trim.

What is the difference between a brad nail and a finish nail?

Brad nails, or brads, are made of 18-gauge steel wire. Nail gauge sizes indicate the thickness of the nail. Thinner nails have higher gauge numbers. Finish nails, or finishing nails, are generally made of 15- or 16-gauge steel wire, making them slightly thicker in diameter than brad nails.

What is the difference between a brad nail and a finish nail?

Brad nails, or brads, are made of 18-gauge steel wire. Nail gauge sizes indicate the thickness of the nail. Thinner nails have higher gauge numbers. Finish nails, or finishing nails, are generally made of 15- or 16-gauge steel wire, making them slightly thicker in diameter than brad nails.

What can I use instead of quarter round?

Shoe molding is much the same as quarter round, having the same 90° angle on the backside but instead of being a perfect quarter radius, its profile is a bit more squat. The main use for shoe molding is to run along the intersection of the baseboard and floor.

Is shoe molding necessary?

Neither caulk nor shoe moulding are mandatory. They are aesthetic decisions and both are used to typically cover gaps. If you don’t like the gaps, use them. If the gaps aren’t there and don’t bother you, no biggie.

What is the point of quarter round?

Most quarter round is of small gauge and relatively flexible. It is typically used as a decorative build-up element in mantels and other architectural features, and at the lower edge of baseboard to hide any gaps between it and a floor.

What size nails do I use for trim?

For trim purposes you should be looking at using 15-, 16-, 18-, or 23- gauge nails. 15 and 16 gauge nailers are the anchors of the pneumatic trim team and are the most versatile for interior trim purposes.

How do you install baseboard molding without a nail gun?

Do you need Quarter round with baseboards?

While quarterround can be installed along the bottom of baseboard, trim carpenters and homeowners tend to prefer the sleeker look of shoe molding, which is taller and narrower than its curved counterpart.

Can you use 18 gauge nails for baseboards?

Both are commonly used for installing baseboard, chair rail, door and window casing, crown molding, and door frames. One advantage to 15-gauge nails is that they are collated at an angle, which allows the nose of the nailer to reach into tighter spaces. Brad nailers use smaller 18gauge nails up to 2 inches long.

Can you glue on baseboards?

Apply a thin bead of construction adhesive along the back length of the baseboard and press it against the wall so the bottom edge is flush with the floor. Hold the board in place for about five minutes to allow the glue to dry. Add some glue to the seams, too.

How do you cut 45 degrees in quarter round?

Quarter round will always be cut at an angle, usually 45 degrees. Cut 2 joint pieces at 45degree angles in the same direction (meaning both angled to the left, or both to the right). These joint pieces should fit together to form a flat line against the wall. Most corners will be 90-degree angles.

Do you glue or nail crown molding?

With one-piece crown, you can only drive nails where there’s framing behind the drywall. In other areas, you have to add nailing blocks or use glue (which often makes a mess or can’t form a strong bond on the narrow edge of the crown molding).

How far apart do you put nails in quarter round?

Choose finish nails that are long enough to penetrate the thickness of the quarter round molding and the drywall with enough left over to go at least 1/2 inch into the wall’s base plate. Place the nails no more than 18 inches apart for 3/4-inch molding.

How do you cut quarter round for corners?

Apply a thin bead of construction adhesive along the back length of the baseboard and press it against the wall so the bottom edge is flush with the floor. Hold the board in place for about five minutes to allow the glue to dry. Add some glue to the seams, too.

How do you cut quarter round for corners?

For ease of installation, it is always best to remove the trim or casing that makes contact with the floor. Ideally, this includes baseboards, door trim and casings, and quarter-round. Often, removing doors helps with installation, too.

Can you glue Moulding?

Apply Loctite Power Grab Molding & Paneling Adhesive to the back of the molding, keeping at least 1/2″ from the edge. Place the trimmed end of the crown molding on the wall next to the corner. The adhesive will keep the molding or trim in place while you tack it in place.

How do you join two pieces of quarter round?

How to Splice Quarter Round Molding
  1. Step 1 – Cut the Molding. Cut the molding at a 45 degree angle then measure the total length.
  2. Step 2 – Work Around Projections. Every room has at least one door, so make butt joints where the baseboard comes up against the door frame without the 45 degree angle.
  3. Step 3 – Splice the Molding.

How do you cut a shoe mold with a circular saw?

It works best on wider molding such as casing, and use a saw equipped with a crosscut blade.
  1. Clamp the molding to the end of a sawhorse face-down so that the end of the molding you wish to cut is extended out past the end of the sawhorse 6 inches.
  2. Measure and make a mark on the molding at the point you want to cut it.

Do you caulk quarter round?

Finishing Touches When Installing Quarter Round Moldings

This is the process of caulking in the quarterly round. When caulking the 1/4 round, run a small bead along the top of the 1/4 round as well as filling in the nail holes. Run your finger along the top to push the caulk into the space.

Do you glue or nail crown molding?

Painting quarter round baseboard once it’s installed can be challenging, so it’s best to apply a coat of primer and at least one finish coat before you nail it in. After making careful wall measurements, use a miter saw to cut 45-degree angles on both ends of each piece.

What can I use instead of quarter round?

Shoe molding is much the same as quarter round, having the same 90° angle on the backside but instead of being a perfect quarter radius, its profile is a bit more squat. The main use for shoe molding is to run along the intersection of the baseboard and floor.

Do you need Quarter round with baseboards?

While quarterround can be installed along the bottom of baseboard, trim carpenters and homeowners tend to prefer the sleeker look of shoe molding, which is taller and narrower than its curved counterpart.

Do you need Quarter round with baseboards?

Quarter round will always be cut at an angle, usually 45 degrees. Cut 2 joint pieces at 45-degree angles in the same direction (meaning both angled to the left, or both to the right). These joint pieces should fit together to form a flat line against the wall. Most corners will be 90-degree angles.

Can I glue shoe molding?

Generally, don’t glue anything that may need to be serviced, unless you’re willing to risk having to destroy it to remove it. You can also pre drill a pilot hole Use a drill bit a tiny bit smaller then the nails. You won’t have a problem bending nails this way.

What nails do you use for quarter round?

Attaching Quarter Round

Because it’s finish trim, install quarter round with finish nails, which have smaller heads than standard nails. A finish nail gun, fitted with 1.5- or 2-inch finish nails, works well. You can also drive finish nails the old-fashioned way — with a hammer.

Do you caulk quarter round?

Finishing Touches When Installing Quarter Round Moldings

This is the process of caulking in the quarterly round. When caulking the 1/4 round, run a small bead along the top of the 1/4 round as well as filling in the nail holes. Run your finger along the top to push the caulk into the space.

How do you install trim without a nail gun?

Hold the finishing tool in one hand, and line it up with your nail. With your other hand, hammer the end of the finishing tool to drive your nail into the trim– nick free. Using spackling compound or wood putty, smooth over the nails completely. Caulk along the top and bottom of the molding.

Should I paint quarter round before installing?

Attaching Quarter Round

Because it’s finish trim, install quarter round with finish nails, which have smaller heads than standard nails. A finish nail gun, fitted with 1.5- or 2-inch finish nails, works well. You can also drive finish nails the old-fashioned way — with a hammer.

Can you glue Moulding?

Apply Loctite Power Grab Molding & Paneling Adhesive to the back of the molding, keeping at least 1/2″ from the edge. Place the trimmed end of the crown molding on the wall next to the corner. The adhesive will keep the molding or trim in place while you tack it in place.

Is shoe molding necessary?

Painting quarter round baseboard once it’s installed can be challenging, so it’s best to apply a coat of primer and at least one finish coat before you nail it in. After making careful wall measurements, use a miter saw to cut 45-degree angles on both ends of each piece.