How to Remove the F9 Code From Maytag
  1. Hold on the “Start/Stop” button for 10 seconds. This will end the beeping.
  2. Open the oven door and check the door latch. If it wiggles, it needs to be tightened.
  3. Spray a little WD-40 onto a washcloth and scrub off any rust or debris on the latch.
  4. Press the oven door shut gently.
  5. Test the oven.

Keeping this in consideration, How do you clear the code on a whirlpool f9?

F8 – Control Board Failure – Replace control board (clock). F9 – Oven Door Lock Failure – Check door lock switches and wiring. Check for stuck lock switch. FH – Detects No Water Entering Machine or No Pressure Switch Trip – Select ‘cancel’ twice to clear this code.

Also know, What does it mean when your stove says f9? An F9 error code on a General Electric (GE) oven indicates that the oven’s electronic control system has detected a problem with the automatic door lock. The malfunction may be a jammed door lock mechanism, a pinched or broken wire, a faulty lock switch or a fault in the control board itself.

21 Related Questions Answers Found


How do I reset my Kenmore Elite washer?

How to Reset a Kenmore Elite HE Washer
  1. Press the “Stop” button twice, and then press the “Power” button.
  2. Choose a wash cycle (e.g. “Normal”), and then choose your wash options (e.g. “Hot/Cold” or “Cold/Cold”).
  3. Press the “Start” button to complete the reset process and restart the washing machine.

What does f31 mean on a oven?

The F31 error code means that the control board detects the oven temperature probe circuit is shorted. I have included a link below on how to test the sensor, and a link to the oven sensor for your model range. If the sensor tests good, then you could have a bad control board or a short in the wiring.

How do I clear the error code on my Whirlpool washer?

To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.

Can I reset my Whirlpool washer?

How do I reset my Whirlpool washing machine? Unplug the washer for 1 minute from the electrical outlet. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. The motor has now been reset and is ready for you to start a cycle.

What does loc mean on a Kenmore oven?

oven lock out feature

How do you fix LF error on Maytag washer?

LF in the display

Check the water inlet hoses to be sure they are not clogged or kinked. You may also need to check the screens on the washer water inlet valve. This means shutting off the water supply, and disconnecting the water inlet hoses from the washer.

How do I reset my Kenmore oven?

How to Reset a Kenmore Elite Stove Oven
  1. Press the “7” button on the Kenmore Elite keypad.
  2. Continue holding the “7” button for at least six seconds until a single beep sounds.
  3. Press the “Start” button on the keypad once. This will reset the oven back to the factory default settings.

How do I stop my Kenmore oven from self cleaning?

What is e1 in washing machine?

From my cursory research an E1 Error code means the machine is trying to fill with water but does not sense that waters enters the machine. This could mean a clogged inlet valve, a failed inlet valve, a clogged pressure sensing line, or a failed water level sensor.

What is FL code on Samsung washer?

The FL error code indicates a faulty door lock assembly. The door lock will attempt to close 7 times before the error code pops up in the display. Opening the door and removing the metal spring around the door gasket. You can use a putty knife or flat head to remove the spring.

How do I fix error code f9?

The F9 error usually means the door switch circuit system is faulty. This can be addressed by checking the door switch itself. If the door switch is dirty or caught in one position, use a damp cloth to wipe the switch clean and then wiggle the switch slightly to make sure the switch moves back and forth.

What is e1 error in Whirlpool washing machine?

Whirlpool Washing Machine FP or F9 E1 Error Code. If your washing machine is not working correctly it’s safe to say it’s developed a fault. A flashing FP or F9 E1 error code on the LCD display can ring alarm bells, but it’s typically associated with a water draining problem inside the drum.

What does f90 mean on a Frigidaire stove?

maximum oven door unlock time was exceeded

How do I fix the LF on my washing machine?

LF in the display

When “LF” is displayed, there could be an issue with the water flowing into the machine. Check the water inlet hoses to be sure they are not clogged or kinked. You may also need to check the screens on the washer water inlet valve.

What does f30 mean on Kenmore oven?

Unplug the washer for 30 seconds to attempt to reset the Duet washer control. You can manually unlock the washer by removing the top (remove screws on the back of the top panel and slide the top panel back to lift off.

What does f30 mean on Kenmore oven?

Whirlpool Cabrio Dryer PF Error Explained

The whirlpool Cabrio dryer PF error means the main control has had a power failure from either a loss of voltage from the power supply or the board itself. Usually a power surge causes the PF error and is easily reset.

How do I lock my oven?

For Automatic Lock Doors:
  1. Make sure the oven is empty.
  2. Touch the CLEAN pad or turn the knob selector to CLEAN on the oven control.
  3. After a few seconds the words LOCK DOOR appear on the panel and/or the LOCK light will come on.
  4. Touch the CLEAR/OFF pad or turn the selector knob to OFF when the clean cycle is complete.

What does F mean on a Whirlpool washer?

The “F” error code indicates the washing machine system or “Fault”. Ehe “E” error is indicating the part in your washer that causing the issue or “Error”. As a general rule, these “F” error codes mean the following… – Whirlpool Duet Washing Machine F5 error code indicates door lock and door switch issues.

How do I reset my Whirlpool Cabrio washer?

How to Reset a Whirlpool Cabrio
  1. Touch any key on the display pad to clear the error code, if applicable, or press “Pause/Cancel.”
  2. Choose a new cycle and press “Start” to begin.
  3. Turn off and disconnect the Cabrio if the error or problem persists.
  4. Wait several minutes before restoring power.
  5. Contact Whirlpool for assistance if the unit will not reset.

How do you stop a Frigidaire self cleaning oven?

If your oven door is locked open, press and hold down the light switch while you continue to work through the process of cancelling the lock on the door. Program your Frigidaire oven to selfclean. Wait at least 20 seconds before you cancel the selfclean setting on the oven. Again wait for at least another 20 seconds.

Which side is hot and cold on washer hookup?

2-4 hours

How do you fix f11 on stove?

The constant beeping and the F11 are caused by a shorted touch pad. You can try and push other touch pads to clear this error. You can remove power to the oven for 2 minutes and turn the power back on and see if the problem has cleared.

How do I reset my Frigidaire oven?

How to Reset a Frigidaire Oven
  1. Press and hold the “Bake” button for six seconds until “0°” appears in the display.
  2. Enter the lower temperature at which you want to reset the oven.
  3. Press “Self Clean” to reset the oven’s internal temperature to a cooler setting.

How do I reset my Frigidaire oven?

If you see “F30” flash on the display of the control panel for your Kenmore stove, you have an error code that indicates there is an open circuit in the wiring of your oven’s sensor probe. To fix the F30 error, you must replace the sensor probe.

What does FO mean on an oven?

Best answer. The F0 error code indicates that the control board detects a stuck key on the control keypad. This is often caused by a bad control keypad but it can sometimes be caused by a failed electronic control board in the oven console. A technician will normally determine which component is causing the problem by.

How do you reset a Kenmore 790 oven?

On most Kenmore ranges that begin with model number 790. . ., you have to press and hold the STOP/CLEAR button for 3 deliberate seconds to unlock the oven door. Try pressing and holding that button for at least 5 deliberate seconds and see if the oven door will unlock.

What does e1 f8 mean on a Whirlpool washer?

There are several possible causes for an F8 E1 Code:

If F8 E1 or LF (too long to fill) appears in display, it means the washer is taking too long to fill. This washer has sensors which detect the water supply, and requires both hoses to have water going to the water valve.

What does lf mean on Bravos XL washer?

long fill

How long does it take for a Kenmore oven to clean itself?

On most Kenmore ranges that begin with model number 790. . ., you have to press and hold the STOP/CLEAR button for 3 deliberate seconds to unlock the oven door. Try pressing and holding that button for at least 5 deliberate seconds and see if the oven door will unlock.

Where is the water inlet valve located on a washing machine?

The inlet valve can be found on the back of your washing machine. Its principal responsibility is to manage the entry of water into your washing machine. In other words, the inlet valve acts as a sort of gate keeper, allowing water to flow into the tub when it receives certain electrical signals from the washer.

What does a washing machine solenoid valve do?

2-4 hours