Whirlpool range error codes
  1. F0. Default F code-no failure.
  2. F1. Defective electronic oven control (EOC)
  3. F2/E0. Keypad wire harness is disconnected.
  4. F2/E5 or F2/E6. Cancel key is defective.
  5. F3/E0. Defective oven temperature sensor or open oven temperature sensor circuit.
  6. F3/E1. Defective oven temperature sensor or shorted oven temperature circuit.
  7. F3/E2.
  8. F3/E3.

Similarly, How do I fix error code f9?

The F9 error usually means the door switch circuit system is faulty. This can be addressed by checking the door switch itself. If the door switch is dirty or caught in one position, use a damp cloth to wipe the switch clean and then wiggle the switch slightly to make sure the switch moves back and forth.

Also, Where is the temperature sensor on a Whirlpool oven? The Whirlpool oven sensor protrudes from the rear wall of the oven and connects to the oven thermostat. As the element heats, the sensor senses the ambient temperature inside the oven.


24 Related Questions and Answers Found 💬

 

Where is the temperature sensor in an oven?

Find the temperature sensor probe in the top left corner of the back wall of the oven interior. Using a 1/4-inch nut driver, remove the 2 hex head screws from the base of the temperature sensor probe.

Why does my stove top work but not my oven?

If your electric oven is not working, but the stove top is, the situation is similar to that of a gas stove. The unit is getting power, as evidenced by the working burners, so there must be something wrong with the oven heating element. The element may be burnt out.

How long does it take to Preheat an oven to 450?

The average time to preheat an oven to 350° is about 15 minutes, but the time varies depending on the stove. Older stoves may take longer to preheat; some newer stove models have a fast preheat feature. If you’re preheating to 450°, add another five minutes to the time.

How long does it take to Preheat an oven to 425?

15 to 20 minutes

How do I reset my self cleaning oven?

Try resetting the oven’s computer by switching the circuit breaker that controls the oven to “off” for 5 minutes. If the oven doesn’t unlock, press the selfcleaning button again to restart the cycle. After 30 seconds, cancel the cycle and see if the door unlocked.

How do you calibrate a Kenmore digital oven?

How to Calibrate a Kenmore Oven
  1. Press and hold the “Bake” button on the front display panel for eight seconds.
  2. Press the “Up” or “Down” arrow on the front display panel to calibrate the oven.
  3. Wait five seconds after you reach the number of degrees more or less you want to change the calibration.

What would cause an oven to not heat up?

Cause: If the temperature sensor inside the oven is not working as intended, it can cause the oven to not heat to the correct temperature. This can be caused by a faulty temperature sensor or a temperature sensor that is touching the wall of the oven.

How do I know if my oven temperature is correct?

The oven temperature sensor is a thermistor which changes resistance depending on ambient temperatures. The sensor is connected to the control by electrical wiring. The control reads the resistance changes in the sensor and reacts, opening and closing electrical relays to switch power to the oven elements on and off.

Do electric ovens have a fuse?

Many electric ranges include a fuse in the 120-volt circuit that operates such items as oven and stovetop lights, the electric clock, convenience outlets, etc. Before repairs or testing can begin you must disconnect the electricity at the fuse panel, at the circuit breaker panel, or by pulling the plug.

How do you reset a Kenmore stove?

How to Reset a Kenmore Elite Stove Oven
  1. Press the “7” button on the Kenmore Elite keypad.
  2. Continue holding the “7” button for at least six seconds until a single beep sounds.
  3. Press the “Start” button on the keypad once. This will reset the oven back to the factory default settings.

Where is the temperature sensor on a Whirlpool oven?

The Whirlpool oven sensor protrudes from the rear wall of the oven and connects to the oven thermostat. As the element heats, the sensor senses the ambient temperature inside the oven.

Will stove turn back on after power outage?

Answer: If an oven on a Gas Range is left on during a power outage, the ignitor senses gas flow and ignites the burner once power is restored. Wolf only recommends lighting gas surface burners when without power, not gas ovens. If the oven does not reignite, turn the oven knob to off, and then back on to reignite.

How do you reset a stove after a power outage?

What causes an oven to overheat?

Before considering replacing your whole appliance, there are a few things that could be causing your oven to get too hot. Typical causes are a faulty thermostat, cooling fan, or oven element – if any of these are not fully functioning it may be the cause of your oven’s overheating problem.

Can you adjust an oven thermostat?

Loosen the screws in the back of the knob. Turn the arrow or pointer to the “Hotter” or “Cooler” position, respectively, to increase or decrease the temperature. The notched increments with each turn is 10 degrees Fahrenheit on some oven models.

How do you unlock the controls on a Whirlpool oven?

To lock the control panel, press and hold LOCK for 3 seconds. An indicator light above Lock will turn on. To unlock the control panel, press and hold LOCK for 3 seconds.

How do I program my Kenmore oven?

How to Use the Delay Start on a Kenmore Oven
  1. Check the time on your oven display, make sure the correct time is displaying.
  2. Set your food in the oven, then close the oven door.
  3. Press the “Bake” button, and then adjust the baking temperature by moving the up or down arrows.
  4. Select “Cook Time.” Program the hours and minutes your dish needs to bake for.

How do I clear f9 code?

How to Remove the F9 Code From Maytag
  1. Hold on the “Start/Stop” button for 10 seconds. This will end the beeping.
  2. Open the oven door and check the door latch. If it wiggles, it needs to be tightened.
  3. Spray a little WD-40 onto a washcloth and scrub off any rust or debris on the latch.
  4. Press the oven door shut gently.
  5. Test the oven.

How do you know when a Kenmore oven is preheated?

Look for an indicator light that shuts off when preheating is done or a light that turns on when the oven reaches the right temperature. Some ovens use animated timers and symbols on the LCD display to help you monitor the preheat cycle.

How do I know if my oven temperature is correct?

Testing the temperature sensor probe on your oven is easy. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature.

How do you calibrate a thermometer?

The oven temperature sensor is a thermistor which changes resistance depending on ambient temperatures. The sensor is connected to the control by electrical wiring. The control reads the resistance changes in the sensor and reacts, opening and closing electrical relays to switch power to the oven elements on and off.

Why is my Whirlpool gas oven not heating up?

If your oven isn’t receiving gas it won’t be able to heat up. To check the gas supply, simply turn on a cooktop burner. If the burner ignites, gas is entering your appliance. On the other hand, if the burner stays unlit, you’ll need to pull your range away from the wall to ensure the gas cutoff valve is open.

Does oven need to be calibrated?

If the average is between 325°F and 375°F, the oven is calibrated. If it’s outside that range, the oven needs adjustment. In this case, consult the owner’s manual. Calibrating some ovens is as simple as turning a screw, but for others, you may have to call a professional to do the job.

Does oven need to be calibrated?

Use an oven-safe thermometer. Place the thermometer on a rack in the center of your oven. Pre-heat your oven to the temperature you’d like to test (350° F, or 177° C) is generally a good recommendation). Once the oven is preheated, check the temperature on the thermometer inside.

How do you replace an oven temperature sensor?

Instructions
  1. Shut off power to the range. Shut off all electricity to the range.
  2. Remove the mounting screws. Remove the oven racks.
  3. Access the wire connector. Carefully pull the oven temperature sensor probe forward into the oven interior.
  4. Disconnect the wire harness.
  5. Install the new temperature sensor probe.
  6. Restore power.

What does oven calibration mean?

Oven Calibration – Controls with Number Pads. If your gas or electric oven temperature does not match your expectations, you can calibrate (adjust) your oven temperature. The oven temperature can be adjusted up to (+) 35°F. hotter or (–) 35°F. cooler.

How long does it take for an oven thermometer to register?

These kitchen gadgets can make cooking simple

While 10 minutes’ worth of preheating time has long been the industry standard, many ovens actually take 15 minutes or more to get up to the programmed temperature. A quick glance at the oven thermometer will let you know when everything’s really good to go.

How do you preheat the oven?

Steps
  1. Consider preheating your oven before starting your recipe.
  2. Open the oven to make sure everything has been removed.
  3. Rearrange the rack levels, if necessary.
  4. Turn the oven on and set the temperature.
  5. Wait until the oven reaches the desired temperature.

What does an oven sensor do?

Oven Calibration – Controls with Number Pads. If your gas or electric oven temperature does not match your expectations, you can calibrate (adjust) your oven temperature. The oven temperature can be adjusted up to (+) 35°F. hotter or (–) 35°F. cooler.

How do I fix the temperature control knob on my oven?

Oven Calibration – Oven Temperature Control Knob
  1. Pull the OVEN TEMP knob off the shaft, look at the back of the knob and note the current setting before making any adjustments.
  2. Loosen both screws on the back of the knob. Each notch changes the temperature by 10 degrees F. To increase the oven temperature, move the pointer 1 notch toward the words “Make Hotter.”

How do you calibrate a Whirlpool electric oven?

The oven temperature sensor is a thermistor which changes resistance depending on ambient temperatures. The sensor is connected to the control by electrical wiring. The control reads the resistance changes in the sensor and reacts, opening and closing electrical relays to switch power to the oven elements on and off.