The easiest way to be certain if the chlorinator is working is to make sure the cell is clean by checking the needle or production lights on the chlorinator box. When operating, you should also see bubbles (hypochloride gas) inside the chamber, producing what looks like cloudy water – that’s chlorine being created!

Similarly, How long do Hayward Salt cells last?

3-5 years

Also, How do you reset the check light on a Hayward? Turn the filter pump on. You must reset the system by entering the ‘Diagnostic Menu’ and then hitting the right arrow key once and then pushing the plus key once. This should reset the light and message.


21 Related Questions and Answers Found πŸ’¬

 

What should my salt generator be set at?

5 Maintenance Tips for Salt Chlorine Generators
  • Try to maintain a consistent salt level of between 2,700 parts per million (ppm) and 3,400 ppm, with 3,200 ppm being ideal.
  • Clean the chlorinator cell at least once a season or as needed.

What should my salt generator be set at?

We suggest you start your salt chlorine generator at 50 percent output and run it for a couple of days, then check the chlorine level. In a balanced pool, a good chlorine level is 1-3 parts per million. If your chlorine levels are low, you can raise the percentage, and if it’s high you can lower the percentage.

How do you convert Aqua Rite to metric?

How to Change the Units of Measurement on an Aqua Rite SCG
  1. Push 1 – To set up for changing units, push the Diagnostic Button one time to display water temperature.
  2. SLIDE MAIN SWITCH UP – Slide the Main Switch from Auto to Super Chlorinate.
  3. SLIDE THE MAIN SWITCH DOWN – Slide the Main Switch back down to “Auto” to save the new units change.

How do I lower the salt in my pool without draining?

Try draining about six inches of water from the pool and refilling with fresh water. Turn on the pool pump to circulate the water, and retest the salt levels. If you’re still at a higher salt level than you prefer, drain another six inches and refill with fresh water again.

How do I lower the salt in my pool without draining?

Try draining about six inches of water from the pool and refilling with fresh water. Turn on the pool pump to circulate the water, and retest the salt levels. If you’re still at a higher salt level than you prefer, drain another six inches and refill with fresh water again.

How do you know when to replace your salt cell?

Power center’s “Cell warning” light comes on and turns off after a cleaning but back on soon afterward. Voltage (higher than normal) and amperage (usually zero) level will show irregular readings. Your salt system is not producing chlorine.

How do you clean a salt cell?

In a clean plastic container, mix a 4:1 solution of water to muriatic acid (one gallon of water to one quart of acid). Caution: ALWAYS ADD ACID TO WATER – NEVER ADD WATER TO ACID. Fasten the Turbo Cell to Cell Cleaning Stand with the cord side down.

How long does a salt cell last for a pool?

Add enough chlorine to bring the Free Chlorine count to reach the Break Point Chlorination Level. Repeat steps 1 & 2 until Break Point Chlorination level is reached or until: The combined chlorine level of your pool drops under 0.5. An overnight Free Chlorine test shows of 1.0 ppm or less.

How do you reset Aqua Logic?

Press the ‘Menu’ until, ‘Default Menu’ appears on the display. This menu is where the ‘Inspect Cell’ message is stored. Press the (>) key, repeatedly, until ‘Inspect Cell, Hold + to reset‘ appears on the display.

How do I know if my flow switch is bad?

You can test the continuity of the flow switch using a Voltmeter or Ohmmeter. Continuity is open if there is no flow. Alternatively, continuity is close if sufficient water flow is detected. If you don’t have access to a VOM, then perhaps the below might help.

How often should I run my saltwater chlorinator?

Salt System Run Times. Your pool system including chlorine generator should be operated often enough to completely turn your pool water over at least every 12 hours or twice a day.

What causes a salt cell to fail?

Salt cells fail for a few different reasons, the main reason being lack of proper maintenance. It is very important to check the cell regularly for excessive buildup. Use a cleaning kit designed for salt cells to keep the plates clear of buildup. Another common cause of salt cell failure is improper water balance.

How do you rebuild a Hayward Salt Cell?

How do I know when to add salt to my pool?

Before adding salt to your pool, test the water to check your salt level. If the level is low, determine the number of gallons in the pool and add salt according to the chart below. A low salt level will reduce the efficiency of your salt chlorinator and result in low chlorine production.

Why is there no free chlorine in my pool?

This occurs when too much stabilizer is added to the water or when the swimming pool isn’t being partially drained and refilled periodically. Chlorine lock can also occur if the pH is unbalanced. If you have a free chlorine reading of 3 and a total chlorine reading of 7, there is a problem.

How do you convert Aqua Rite to metric?

How to Change the Units of Measurement on an Aqua Rite SCG
  1. Push 1 – To set up for changing units, push the Diagnostic Button one time to display water temperature.
  2. SLIDE MAIN SWITCH UP – Slide the Main Switch from Auto to Super Chlorinate.
  3. SLIDE THE MAIN SWITCH DOWN – Slide the Main Switch back down to “Auto” to save the new units change.

Can a salt cell be repaired?

Salt Chlorine Generators do require some maintenance and repair. The salt cell will eventually lose performance and the controller circuit boards can develop problems over time. New technology in salt systems may also sway your decision to repair or replace your salt chlorinator.

How do I unlock my Hayward configuration menu?

Press the ‘Menu‘ until, ‘Configuration Menu-Locked’ appears. To unlock, press and hold the (<) & (>) until the text, on the display, changes from ‘Locked’ to ‘Unlocked‘ (unit will beep). Press the (>) repeatedly, until ‘Chemistry Config.

How long does a chlorinator cell last?

about five years

How long does a salt cell last for a pool?

The first option for testing uses a liquid chemical OTO (orthotolidine) that causes a color change to yellow in the presence of total chlorine. You simply fill a tube with water, add 1-5 drops of the solution, and look for the color change.

Why is my chlorinator not working?

The salt cell generators are made to work when pool water temperatures are above 60 degrees. In pool water temperatures that are 60 degrees or below, the salt generators simply shut down and by design do not allow the salt cell to ionize (breakdown) the salt and convert it to chlorine.

When should you replace a salt cell?

Most salt chlorine generators have a salt cell that lasts typically from 3 to 5 years, you should check with the manufacturer to double check the life expectancy. Most salt chlorine systems come with a control panel or a self regulating system that will tell you when the cell needs to be cleaned or replaced.

How do you clean a salt cell without a stand?

If you do not have a cell stand, carefully place the cell in a plastic bucket and add the acid wash solution until the plates are covered. Make sure not to cover the cell electrical connections. Again, let the unit soak for 15 minutes. After the soak, rinse the cell again with a garden hose.

How do you clean a salt cell without a stand?

about five years

Why is my chlorinator not making chlorine?

A salt chlorinator cannot produce enough chlorine to do this task. Seek assistance from your local pool shop for the required procedure for your pool. Algae is the most common cause of low or zero chlorine levels.

Why is my saltwater pool not making chlorine?

Salinity. Chlorine generators need salt to produce chlorine and can’t do so if the amount of salt in the water is too low. Get a salt-testing kit from a pool supplier and check to make sure that the levels are within this range. If your salinity is below 2,500 ppm, the generator will not be able to produce chlorine.

What does free chlorine mean?

Free chlorine refers to both hypochlorous acid (HOCl) and the hypochlorite (OCl-) ion or bleach, and is commonly added to water systems for disinfection. Chloramines are also known as combined chlorine. Total chlorine is the sum of free chlorine and combined chlorine.

Why do salt cells stop working?

Salt cells fail for a few different reasons, the main reason being lack of proper maintenance. It is very important to check the cell regularly for excessive buildup. Doing this ensures excess calcium doesn’t become caked on the metallic plates. Another common cause of salt cell failure is improper water balance.

What temperature does a Salt Cell stop working?

Salinity. Chlorine generators need salt to produce chlorine and can’t do so if the amount of salt in the water is too low. Get a salt-testing kit from a pool supplier and check to make sure that the levels are within this range. If your salinity is below 2,500 ppm, the generator will not be able to produce chlorine.

How does a salt chlorine generator work?

Electrolytic chlorine generators (ECGs), or salt water chlorinators, use electricity and dissolved salt to produce chlorine for the pool. As electric current passes through the cell, it generates chlorine gas, which provides a free available chlorine residual to the water.

What is a salt chlorine generator?

The salt cell generators are made to work when pool water temperatures are above 60 degrees. In pool water temperatures that are 60 degrees or below, the salt generators simply shut down and by design do not allow the salt cell to ionize (breakdown) the salt and convert it to chlorine.