You can reset your dryer to the default settings it left the factory with:
  1. Press and hold the ‘Keylock’ and ‘Delicate’ buttons together for three seconds.
  2. Your dryer will now be reset to the default settings.

Similarly, How do you take apart a Fisher and Paykel washing machine?

How to disassemble Fisher and Paykel smartdrive electronic washing machine
  1. Isolate from the power supply.
  2. To remove the lid, open it to the upright position and lift it clear.
  3. Remove the 2 screws from the rear of the top console, disconnect the earth lead.
  4. Disconnect the pressure tube from the pressure sensor.

Also, How do I level my Fisher and Paykel washing machine? Place the level at the centre front of the topdeck, forward of the lid lock slot. Check the machine is level. Move the level around to all positions once more, checking the machine is level in all areas. Check that the machine does not rock in any direction.


29 Related Questions and Answers Found ๐Ÿ’ฌ

 

Why is my Fisher and Paykel washing machine not spinning?

Check the amount of detergent used, reduce if necessary, or try using less or a low-sudsing detergent as this can affect a spin cycle. Straighten any kinks along the hose that drains water from your washer. If the kinks return, you may need to replace the hose. Open door and redistribute load, then restart the washer.

How do you replace the Fisher Paykel control board?

How to Replace the Control Board on a Fisher Paykel Dishwasher
  1. Flip the switch at your electrical breaker box to the โ€œOffโ€ position to turn off your Fisher & Paykel dishwasher.
  2. Pull the bottom drawer out as far as it will go and lift out the dish rack.
  3. Look inside the tub on the bottom drawer.
  4. Remove each of the pins with needle-nose pliers by clasping the pin and pulling it out.

How do I reset my Fisher and Paykel?

Reset Procedures for the Fisher & Paykel Dishwasher
  1. Press and hold the button decorated with the key and lock image for five seconds.
  2. Press the power button to turn off power to the Fisher & Paykel dishwasher.
  3. Wait a few minutes and then press the power button to restore power.
  4. Turn off and unplug the dishwasher if the issue remains.

Why is my washing machine beeping mid cycle?

Washer sounds and beeps

Your machine is checking that the water has drained before spinning. Your washer will beep if you have used ‘No Spin’ and at the end of the cycle. If your machine is beeping continuously or giving a musical series of beeps, refer to the ‘Before you call for service’ section.

How do I reset my Fisher and Paykel dishwasher?

Reset Procedures for the Fisher & Paykel Dishwasher
  1. Press and hold the button decorated with the key and lock image for five seconds.
  2. Press the power button to turn off power to the Fisher & Paykel dishwasher.
  3. Wait a few minutes and then press the power button to restore power.
  4. Turn off and unplug the dishwasher if the issue remains.

How do you use Fisher and Paykel WashSmart?

Using your washer
  1. Press ‘Power’ to activate your WashSmartโ„ข washer.
  2. Select your desired wash cycle by pressing the wash cycle button of your choice (refer to ‘Wash cycles’ section).
  3. Choose your wash options, eg you may want a ‘Warm’ wash temperature and a ‘Slow’ spin speed (refer to the ‘Wash options’ section).

Is there a reset button on a Fisher and Paykel washing machine?

Factory Reset

Turn the dial to select ‘Spin’. Touch and hold the ‘Delay Start’ ‘More’ , the ‘Delay Start’ ‘Less’ and ‘Options’ buttons together for 3 seconds will appear on the screen and the machine will beep. Your washer will now be reset to the default settings.

Cleaning the Pump Filter
  1. Turn the power off and unplug the machine.
  2. Use a coin to open the filter cover.
  3. Unhook the pump outlet hose and pull it out (about 150mm).
  4. After the draining process is complete, replace the plug into the hose and refit the hose back into the housing.
  5. Remove the filter by turning anti-clockwise.

How long should a washing machine last?

The average life expectancy of a new washing machine is 11 years. Consumer Reports recommends replacing any appliance that’s more than eight years old, unless it’s a high-end model and has a particular appeal to you. Others suggest replacing any top-loading washer manufactured in 1999 or earlier.

How do you unlock the door on a Fisher and Paykel front loader?

To unlock the door during the cycle

Simply touch , the machine will pause and the door will automatically unlock if the conditions inside the washer are safe. The button and time to go will flash on the screen while the washer is paused. Open the door and remove or add garments.

How do you remove the drum from a Fisher Paykel washing machine?

How to Remove the Tub on a Fisher & Paykel Washer
  1. Lift out the two lid bumpers located on the top of the machine.
  2. Take the lid off or move the washer away from the wall so you can lift the lid and lean it back.
  3. Unclip the bias spring located on the left of the support strut, but do not detach from the ring.

How do I know if my washing machine motor is bad?

The five most common signs of motor issues are listed below.
  1. Washer Won’t Pump or Spin. It may happen that the washing machine fails to pump water in and out, as well as spin.
  2. Pumps, but Won’t Spin.
  3. Washer Won’t Agitate.
  4. Clothes Still Wet.
  5. Problems in Every Cycle.

Why is the washing machine beeping?

How do I reset my Fisher and Paykel ecosmart washing machine?

Unplug the unit at the wall. Wait 20 seconds and then plug the unit back in and press “Power.” Resetting the washer can often fix the problem. Turn on the hot and cold faucets leading to the machine to ensure water is feeding into the machine.

What does key lock mean on Fisher and Paykel washing machine?

The Key Lock mode disables the control panel so that the storage environment cannot accidentally be changed. The display will automatically lock after 15 seconds of the display not being used or when the drawer is closed. The red lock icon will appear above the Lock button when the panel is locked.

Why is my Fisher and Paykel washing machine not spinning?

Check the amount of detergent used, reduce if necessary, or try using less or a low-sudsing detergent as this can affect a spin cycle. Straighten any kinks along the hose that drains water from your washer. If the kinks return, you may need to replace the hose. Open door and redistribute load, then restart the washer.

How do you clean a Fisher and Paykel drum?

Cleaning the drum and the door
  1. Use a soft damp cloth to wipe the door, cleaning any water marks or residue off it.
  2. Wipe the rubber seal around the door.
  3. If the drum has any residual dirt or lint stuck to it, remove this and wipe the drum clean.

Why is my washing machine not working?

If your washer fills with water but doesn’t agitate, the problem is likely to be a faulty lid switch, a broken belt, or a problem with the motor. 1 Check the washing machine’s spin cycle. If this works, the motor is operating and the belt is not broken. If the spin cycle doesn’t work, the belt may be loose or broken.

Why does my Fisher and Paykel dishwasher keep beeping?

The drain filter must be level with the filter plate. Close the drawer and press the button. The DishDrawerยฎ will beep six times to indicate the end of the wash programme. At the end of the wash programme the drying fan will continue to run for a set time or until the drawer is opened.

Factory Reset

Turn the dial to select ‘Spin’. Touch and hold the ‘Delay Start’ ‘More’ , the ‘Delay Start’ ‘Less’ and ‘Options’ buttons together for 3 seconds will appear on the screen and the machine will beep. Your washer will now be reset to the default settings.

How do you troubleshoot a Fisher Paykel washing machine?

Why does my washing machine not spin all the water out?

If your washer will not spin out all water and clothes are still wet, the drain pump might be clogged with debris or possibly faulty. There could be a foreign object that is stuck in the pump and inside the drain hose. Test to be sure the drain pump is working properly.

How do I start a Fisher and Paykel washing machine?

Choose your wash options, eg you may want a ‘Warm’ wash temperature and a ‘Slow’ spin speed (refer to the ‘Wash options’ section). Use to advance through to the desired part of the wash cycle. Press to start the cycle. The washer will start to fill with water and select the correct wash action for your load.

How do I clean the filter on my top load washing machine?

Part 2 Cleaning Your Filter
  1. Use a paper towel to remove any lint from the filter.
  2. Remove the screen from the filter and soak it in hot water for 10 minutes.
  3. Inspect the inside of the machine for excess lint.
  4. Replace the filter and the outer cover.
  5. Run your empty washer to test for leaks.

How do you drain a Fisher and Paykel dishwasher?

How to Unclog a Fisher & Paykel Dishdrawer Drain
  1. Obtain a copy of the instruction manual for your specific model of Fisher & Paykel dishwasher.
  2. Use the diagrams in the manual to locate the food trap.
  3. Use the diagrams in the manual to locate your dishwasher’s drain hose.
  4. Disconnect the drain hose at both connection points.
  5. Look up the pump assembly in the manual.

How do you run a diagnostic on a Fisher Paykel washing machine?