To adjust the left stop, simply turn the screw on top clockwise to increase angle (40-360). A quarter of a turn increases it approximately 90 degrees. To adjust spray distance, locate small screw on the top of nozzle. Turn counter clockwise to increase spay or clockwise to decrease spray distance.

Keeping this in consideration, How do you change the direction of a sprinkler head?

To increase the arc of your Hunter rotor head, you’ll want to insert the plastic key into the adjustment socket, which can be found on the top of each sprinkler head. Turn the adjustment wrench clockwise in a full 360-degree motion. This will increase your arc by 90 degrees each time you turn the wrench a full circle.

Also know, How do you fix a sprinkler head that won’t turn?

How to Do It
  1. Disassemble the sprinkler head.
  2. Take off the filter at the bottom of the head.
  3. Rinse the filter in a bucket filled with clean water to wash out debris.
  4. If this doesn’t work you’ll need to have the sprinkler head replaced.
  5. If it does work, make sure the head is properly adjusted when you re-install it.

34 Related Questions Answers Found


How do you adjust a maxi paw sprinkler head?

  1. Place the flat tip of a Rain Bird wrench under the top cap on the Maxi-Paw 2045A sprinkler head and raise it upward out of the ground.
  2. Insert the wrench around the sprinkler body below the spray adjustment controls and turn it clockwise until the wrench locks in place on the sprinkler.

How many zones do I need for my sprinkler system?

The resulting number will equal how many zones you need. If, for example, each sprinkler head will require a flow rate of 1.31 GPM and you have 20 of them, then you will need 26.2 GPM total. If your system can only handle 16.67, you will need to use two zones to cover that same area of your yard.

Are sprinkler heads interchangeable?

A replacement sprinkler head doesn’t have to be the same brand as the broken head. But it does have to be the same type: pop-up (stationary, rotor- or gear-driven rotor) or impact. If you can’t find the specifications, at least find the brand and part number.

How do you adjust a rotating sprinkler?

Sprinklers may be adjusted with water on or off. It is recommended that initial adjustments be made before installation. Using the palm of your hand, rotate the nozzle turret counterclockwise to the left stop to complete any interrupted rotation cycle. Rotate the nozzle turret clockwise to the right stop.

Why is my sprinkler not rotating?

Age, excessive pressure, or poor water quality may eventually allow particles of contamination to enter the gear drive. If the sprinkler is no longer rotating and the water flow coming out of the sprinkler has decreased, you can first try cleaning out the filter by removing the pop-up assembly from the main body.

How do you adjust a Rainbird 5000 left stop?

Adjust the Right Stop of the Rainbird 5000 Sprinkler Head.
  1. Once the left side is set you can now, set the right stop, this is done with the key or a flat head screwdriver.
  2. Rotate the turret all the way to the right side and as you turn it back towards the left side, stop turning it where you want the right side to stop.

Can you shut off one sprinkler head?

Rotor (or gear heads) can not be shut off. You have to unscrew the head out of the ground and cap it off.

How do I know if my sprinkler head is capped?

How do you change the direction of a sprinkler head?

To increase the arc of your Hunter rotor head, you’ll want to insert the plastic key into the adjustment socket, which can be found on the top of each sprinkler head. Turn the adjustment wrench clockwise in a full 360-degree motion. This will increase your arc by 90 degrees each time you turn the wrench a full circle.

Does Home Depot carry Rain Bird?

Rain Bird – The Home Depot. To see what’s in stock near you, please enter you zip code or local store number.

How do you remove an old sprinkler system?

To remove a sprinkler you can sometimes just grab the top of it and turn it counter-clockwise. It will unscrew from the pipe below it and then you can lift it out of the ground. Often you will need to dig away grass from it so you can twist it out.

How many impact sprinklers can I run at once?

For example, you generally have a flow rate of 10 gpm from a ¾-inch spigot where you connect your hose. With your 10 gpm flow rate at your spigot, you could run two sprinklers at 5 gpm each. The best set-up is to run two hoses from the spigot–each to one sprinkler.

Can you cap a sprinkler head?

To cap a sprinkler head, you‘ll have to remove the existing sprinkler cap and replace it with a flat cap that will prevent water from flowing into that head. You can also completely remove the sprinkler head and cap it with a PVC pipe cap.

How lawn sprinkler heads work?

The sprinkler heads work on a pressure system that when the water goes through the pipe, it pushes them up above the ground. When the water pressure stops, they retract back down to ground level. Sprinkler heads in a garden are usually a raised-head type.

Rain Bird® Simple Adjust Series Rotors
  1. Find and set the fixed LEFT edge. First, turn the center cap of the rotor all the way to the right until it stops. Then turn it to the left until it stops.
  2. Adjust the arc pattern. The arc is preset to rotate 180º or a half circle.
  3. Adjust the spray distance. With the water on or off, you can adjust the distance of throw.

Usually it’s about 30 minutes. So 20 minutes, 3 times per week will get an inch of water on your lawn, and 30 minutes 3 times per week will get 1 ½” down. Bear in mind that during extreme heat, you will need to water more, due to evaporation and heat stress on the grass.

Do you use Teflon tape on sprinkler heads?

For irrigation systems the recommended sealer is PTFE thread seal tape (often called Teflon® tape.) Do not use “pipe dope” (liquid or paste type sealers) on irrigation systems! Look on the bottom of many sprinklers and you will see the warning “Don’t use pipe dope”.

How do you adjust a 42sa sprinkler head?

Locate the arc adjustment screw, which is one of two screws on the rotor head. The arc adjustment screw is the one with the “+” and “-” signs along side of it. The device is preset to turn 180 degrees. Turn this screw clockwise with a flat-head screwdriver to increase the rotation arc and counterclockwise to reduce it.

How does pop up sprinkler work?

The controller sends a signal to the control valves in the control valve box. The sprinkler system valves open, sending water through the underground water line, which causes the sprinkler heads to pop up and spray.

Why do sprinkler heads leak?

There are two reasons why a sprinkler will leak water when the system is supposed to be off. The most common reason is called “Low Head Drainage”. “Low Head Drainage” occurs when the lowest head on a zone allows water to drain from the lateral piping, out of the sprinkler.

Why do sprinkler heads stop rotating?

Damaged Internal Components

These gears must be lubricated to move freely. In most cases, water is the lubricant. But some sprinkler heads contain a small amount of oil inside that lubricates the gears. If the oil dries out or leaks, it can cause damage to the internal gears, and the rotating motion will stop working.

How do I adjust my sprinkler pressure?

Adjust the master valve of your sprinkler system by turning the flow control clockwise until the stream of water from the nozzle begins to drop. This lowers the water pressure. Turn the flow master valve flow control slowly until the spray pattern reaches its full radius.