Eight Feet or Lower

Use your room height measurement to help determine the width of the crown molding. Install a crown molding between 3 and 5 3/4 inches wide in a room with ceilings measuring 8 feet. A larger room can support a wider crown molding, while a more narrow molding will work better in a smaller room.

Hereof, How do you fix gaps in corner of crown molding?

After crown molding installation, there is usually a large gap between the crown molding and the wall or ceiling. Latex caulk is a good way to fill these gaps. Spread a bead of caulk along the gap with a caulk gun. Smooth the caulk with your finger and let the caulk dry overnight.

Does crown Moulding add value? Does Crown Molding Increase Appraisal Value? Anything that gives a house a more stylish or elegant appearance will raise its appraised value. Simple, inexpensive additions like crown molding can add dollars when an appraiser walks through your house – but only if the crown molding is done correctly and tastefully.


25 Related Questions Answers Found

 

Should I add crown molding?

It is fine to have it in some rooms, while not using it in others. Certain rooms in the house are almost always a desirable place for crown molding. For example, the living room is a classic location to use it. If you have cathedral or vaulted ceilings, a typical crown molding will probably not fit or look good.

What size nails do you use for crown molding?

Crown is typically nailed up with a 2” finishing nail and a compressor and finishing gun. Outside corners are usually done with a brad nailer and 1” brad nails with glue. Studs are generally 3-1/2”, drywall a ½” and the crown moulding a minimum of ½”; therefore 2” finishing nails are necessary.

How do you cut crown molding for dummies?

While learning how to cut crown moulding, remember: Using a power miter saw is the best way to cut crown moulding angles. The saw can be adjusted to cut at any angle–set it to 45 degrees for one side of a standard 90-degree corner. The saw can be set to 45 degrees to the left or 45 degrees to the right.

How do you cut and install crown molding?

To install crown molding:
  1. Measure the length of each wall.
  2. Set the miter saw to a 45Β° angle.
  3. Position the bottom of the molding against the saw fence and table.
  4. Tilt the molding so the back is flush with the saw fence.
  5. Cut the crown molding to length.
  6. Hold the molding on the wall, and nail it in place to the studs.

Can I use a brad nailer for crown molding?

Both are commonly used for installing baseboard, chair rail, door and window casing, crown molding, and door frames. One advantage to 15-gauge nails is that they are collated at an angle, which allows the nose of the nailer to reach into tighter spaces. Brad nailers use smaller 18-gauge nails up to 2 inches long.

How do you choose crown molding for kitchen cabinets?

How to Choose Crown Molding for Cabinetry
  1. Crown style: Square. Clean and simple. Works with modern or shaker.
  2. Crown style: Curved cove. Softer than the square. Transitional.
  3. Crown Style: Cove with bead on top and bottom. A little extra detail.
  4. Crown Style: Traditional. More curvature and ridges to the crown.

Does crown molding make room look bigger or smaller?

Crown molding does not make a room look smaller — in most instances. The molding can be wider if the ceiling is a little higher and can be up to 6 inches wide for a very high ceiling — up to 12 feet. Crown molding any wider than this is only suitable for very large rooms or very tall ceilings, or both.

What size crown molding should I use for 8 foot ceilings?

Does crown molding add value to a home?

Does Crown Molding Increase Appraisal Value? Anything that gives a house a more stylish or elegant appearance will raise its appraised value. Simple, inexpensive additions like crown molding can add dollars when an appraiser walks through your house – but only if the crown molding is done correctly and tastefully.

Why do you have to cut crown molding upside down?

Why Cut Crown Molding Upside Down and Backwards? Chris Marshall: Crown molding is typically cut upside down on a miter saw so the narrow edge that will rest against the wall butts against the saw fence and the top edge of the molding that will meet the ceiling rests on the saw table.

Where should you nail crown molding?

Crown molding is usually nailed to the wall studs along the bottom edge and into the ceiling joists above–a lot of stud-finder work.

What is the difference between 52 38 and 45 45 crown molding?

To find out what the spring angle is, set the crown molding into the crotch of a framing square and check where the ends align. if both numbers are the same, it is 45/45 crown. If the numbers are different, such as three inches on the wall and two inches on the ceiling, it is 52/38 crown.

Which nailer is best for installing crown molding?

Our Top 5 Best Nail Gun For Crown Moulding:
  • NuMax SFN64 Pneumatic Nail Gun.
  • Hitachi NT65M2S.
  • NEU MASTER NTC0040 Electric Nail Gun/Staple Gun.
  • NuMax S2-118G2 2-in-1 Brad Nailer and Stapler.
  • Freeman P4FRFNCB Pneumatic Framing & Finishing Combo Kit.

What can I use instead of crown molding?

Medium-density fiberboard (MDF) is another popular alternative to the traditional wooden crown molding. It is installed very much the same way as real crown molding but is cheaper and more lightweight. MDF crown molding is also very customizable, as it can be stained or painted to the color you desire.

What are the angles for crown molding?

Crown molding is usually nailed to the wall studs along the bottom edge and into the ceiling joists above–a lot of stud-finder work. I skip all that by installing a plywood backer board to the top plate (the horizontal framing member above the wall studs).

What are the angles for crown molding?

Our Top 5 Best Nail Gun For Crown Moulding:
  • NuMax SFN64 Pneumatic Nail Gun.
  • Hitachi NT65M2S.
  • NEU MASTER NTC0040 Electric Nail Gun/Staple Gun.
  • NuMax S2-118G2 2-in-1 Brad Nailer and Stapler.
  • Freeman P4FRFNCB Pneumatic Framing & Finishing Combo Kit.

What kind of nail gun do I need for crown molding?

A finish nailer is a versatile tool, and drives either 15- or 16-gauge nails. They are used for smaller projects than framing nails, such as crown molding, baseboards, cabinets, chair rails, decorative trim, millwork, and hardwood flooring.

What rooms should have crown molding?

As we mentioned, crown molding is often installed between walls and the ceiling or the wall and the floor. This gives the room a seamless, elegant appearance.

Here are a few:

  • Kitchen Cabinets.
  • Bathroom Mirrors.
  • Bedroom Headboard.
  • Shelving.
  • Around Your Mounted TV.

How long should nails be for crown molding?

Crown is typically nailed up with a 2” finishing nail and a compressor and finishing gun. Outside corners are usually done with a brad nailer and 1” brad nails with glue. Studs are generally 3-1/2”, drywall a ½” and the crown moulding a minimum of ½”; therefore 2” finishing nails are necessary.

Will Brad nails hold in drywall?

A brad nail will easily detach or pull away from drywall surfaces which is why a finish nailer is the best option.

Which is the top of crown molding?

Cut a 45-degree angle in a piece of trim with a miter saw.
  1. Doing this is similar to cutting an outside corner. You can cut another piece of trim at a 45-degree angle and install them on the wall right away.
  2. Inside corners are where 2 walls meet to form a concave angle. It is common in baseboards and crown molding.

Why do you have to cut crown molding upside down?

Why Cut Crown Molding Upside Down and Backwards? Chris Marshall: Crown molding is typically cut upside down on a miter saw so the narrow edge that will rest against the wall butts against the saw fence and the top edge of the molding that will meet the ceiling rests on the saw table.

How do you cut a 45 degree crown molding flat?

So the crown molding sits upside down on the saw. The saw blade can be swung 45 degrees, and the blade will slice a perfect compound miter in the crown. The other way to cut the crown molding it to lay it flat on the table and use the bevel adjustments of the blade to dial in the correct compound miter angles.

How do you cut a 45 degree crown molding flat?

Crown molding with a 38 degree spring angle is so common, in fact, that many miter saws are equipped with pre-set detents or marks at the 31.6 degree miter and 33.9 degree bevel settings used for 90 degree corners.

What is a spring angle crown molding?

Definition of Crown Spring Angle

The crown spring angle is the angle measured from the back of your crown molding to the wall when holding the bottom of your crown molding firm against the wall (in full contact with the wall).

What is a miter cut vs bevel?

A miter cut refers to an angled cut on the face of two structures, which will be joined to make a corner called the miter joint. A bevel cut refers to an angled cut along the edge or end of the material. Miter cuts are made by pushing the flat on the table at an angle to the blade.

How hard is it to install crown molding?

The hardest part of installing crown molding is cutting the corners. You can’t do it like any other trim pieces because the molding sits at an angle between the wall and the ceiling (Image 1). Using a coping saw (Image 2) is the easiest way to cut the corners because a coped joint is tighter than a mitered joint.

What size nails do you use for crown molding?

Both are commonly used for installing baseboard, chair rail, door and window casing, crown molding, and door frames. One advantage to 15-gauge nails is that they are collated at an angle, which allows the nose of the nailer to reach into tighter spaces. Brad nailers use smaller 18-gauge nails up to 2 inches long.

What angle do you cut trim at?

A miter cut refers to an angled cut on the face of two structures, which will be joined to make a corner called the miter joint. A bevel cut refers to an angled cut along the edge or end of the material. Miter cuts are made by pushing the flat on the table at an angle to the blade.

What is the purpose of crown molding?

Crown molding encapsulates a large family of moldings which are designed to gracefully flare out to a finished top edge. Crown molding is generally used for capping walls, pilasters, and cabinets, and is used extensively in the creation of interior and exterior cornice assemblies and door and window hoods.

Do you have to nail crown molding into studs?

Cut a 45-degree angle in a piece of trim with a miter saw.
  1. Doing this is similar to cutting an outside corner. You can cut another piece of trim at a 45-degree angle and install them on the wall right away.
  2. Inside corners are where 2 walls meet to form a concave angle. It is common in baseboards and crown molding.