Hold the gas control button down while you hold the end of a lighted match or lighter at the end of the pilot tube. If you do this correctly, the pilot light should start as soon as the flame is close enough. Hold the pilot button down for about 20 seconds to give the thermocouple time to heat up, then release it.

Also, How does a fireplace switch work?

When the thermocouple is heated by the pilot light, it generates a very small electrical voltage (millivolts) which can be run through a switch to turn on a Milli-volt gas valve (as opposed to a 24 volt gas valve used with a conventional thermostat).

In this way, How do you replace a thermocouple on a Heat and Glo fireplace?

How to Remove the Thermocouple in a Heat & Glo Fireplace
  1. Turn the gas valve on the front of the Heat & Glo fireplace to the “Off” position.
  2. Place a sheet or some newspaper on the floor in front of the fireplace.
  3. Loosen the nut securing the thermocouple to the rear of the gas valve with a wrench.
  4. Pull the end of the thermocouple out of the back of the gas control valve.

20 Related Questions Answers Found

 

How do you replace a thermocouple on a Heat N Glo fireplace?

How to Remove the Thermocouple in a Heat & Glo Fireplace
  1. Turn the gas valve on the front of the Heat & Glo fireplace to the “Off” position.
  2. Place a sheet or some newspaper on the floor in front of the fireplace.
  3. Loosen the nut securing the thermocouple to the rear of the gas valve with a wrench.
  4. Pull the end of the thermocouple out of the back of the gas control valve.

Why does my gas fireplace go out after a few minutes?

1) There’s enough gas flow to maintain the pilot light, but after you burn the larger flame a few minutes pressure drops too low to support the larger flame and it goes out. Pressure builds in the header while you scratch your head, allowing you to run it a few mintues again until pressure drops too low again.

How do you light a pilot light on a propane fireplace?

Press the fireplace safety pilot control knob down and hold it as you turn it over to the pilot position. Continue to hold the knob down for five seconds to give the propane enough time to flow through the hose that connects the propane gas line to the fireplace.

How does a gas fireplace wall switch work?

HOW DOES YOUR GAS FIREPLACE START? When you flip a wall switch, click on your remote control or the thermostat calls for heat, the gas valve on your fireplace will open. Gas valves generate their own electricity and operate on millivolts, a very small amount of electricity.

Is a gas fireplace worth it?

Is a gas fireplace worth it? Yes! Gas fireplace benefits are incredibly attractive and convenient; especially for a busy family like yours. You’ll get instant heat, pinpoint control, terrific safety and other things which a wood burning fireplace simply can’t deliver.

What is a Heat and Glo fireplace?

Heat & Glo is the innovative leader in technology, design and safety. Search through the entire Heat & Glo lineup of gas fireplaces, gas fireplace insert products, wood fireplaces, stoves and inserts to find out why “No One Builds a Better Fire.” Heat & Glo carries a wide variety of gas, wood and electric fireplaces.

What is a B vent fireplace?

Bvent gas fireplaces, also known as natural vent fireplaces, or as a b vent fireplace, use air from inside your home to fuel combustion and rely on the buoyancy of hot gases to vent exhaust through dedicated pipe systems.

How much is a Heat and Glo fireplace?

Is it dangerous if pilot light goes out on gas fireplace?

A small flow of gas powers the pilot light – just enough to maintain a flame. When a pilot light goes out on a gas fireplace, there is cause for concern if the gas flow hasn’t been interrupted. More commonly, a pilot light will go off because of a failure in the supply of gas.

Will gas leak if the pilot light goes out?

Carbon monoxide is a colorless, odorless gas produced during burning fuel. It doesn’t leak from a pilot light that’s gone out, but if the light keeps going out even after you relight the pilot, it can indicate that you have other problems.

How safe are gas fireplaces?

Gas fireplaces are safe. But as with all gas appliances, they do produce carbon monoxide. If something goes wrong, carbon monoxide put the home’s occupants at risk. Therefore, carbon monoxide detectors are a critical part of gas fireplace safety, even if you don’t use the fireplace often.

How do I light a gas fireplace?

Turn the knob from the “Off” to the “Pilot” position. Push in the pilot knob, which manually sends gas into the system. Push the igniter button once every second until it lights. Depending on how long it’s been since the gas fireplace was last used, ignition may take multiple attempts.

Do direct vent fireplaces provide heat?

Efficiency. Direct vent fireplaces burn natural gas or propane like traditional fireplaces; however, they convert most of the fuel to usable heat. They are completely sealed off from the interior rooms by a glass door, which prevents significant heat loss.

Why is my gas fireplace not turning on?

1. Pilot light systems are the most common reason gas fireplaces fail to light, so check the main gas valve to make sure the gas is turned on. It should usually run parallel to the gas line when it is on. The pilot lights, but not staying lit, indicates that the thermocouple is worn out or bad.

How do you know if your furnace pilot light is out?

Here are good reasons to turn off your gas fireplace pilot in the summer: When your pilot light remains on, a small amount of heat is generated. The glass doors on your gas fireplace remain warm to the touch. When your pilot light is off, you save money and help to conserve energy.

How do you know if your furnace pilot light is out?

Your water heater does not have an ignitor. The pilot should always be burning on your water heater. Sometimes the pilot flame is hard to see through the viewing window. To be sure if the pilot is on or off, you need to remove the access door and shield and look at the burner and pilot through the opening.

Is it dangerous if the pilot light goes out on furnace?

Can a Pilot Light Outage Be Dangerous? The worry here is that when a pilot goes out, the gas valve that supplies the fuel for the pilot flame could still be pumping gas. This can mean a buildup of gas, and when the pilot is relit or relights itself it could result in a very serious explosion.

Is it dangerous to light a pilot light?

Yes, it is safe to light a pilot light with a gas lighter. If you are trying to relight the pilot light, before turning the knob to the pilot position, wait for some time until the gas smell goes away. If you follow these instructions, it is safe to light a pilot light using gas lighter.

Is it OK to leave gas fireplace on overnight?

It usually runs all night. However, unvented gas fireplaces (aka vent free, ventless) can adversely affect indoor air quality and shouldn’t be used more than a few hours at In most cases, if your fireplace was installed properly, you can leave it on indefinitely.

Do all gas furnaces have a pilot light?

For many years, furnaces used a small and continuously burning flame known as a pilot light to ignite the burners during every heating cycle. Although pilot lights are still present in homes with older systems, most newly installed furnaces use an electronic ignition instead.

Do gas fireplaces use a lot of gas?

Resetting a Gas Furnace
  1. Check to see if your pilot light is out.
  2. Turn down your thermostat as low as it can go.
  3. Turn off the power to the furnace.
  4. Turn off the main gas supply to the furnace.
  5. Light a match and hold it to the pilot flame jet’s opening, which is inside the furnace.

Why is my boiler not igniting?

Burner won’t ignite: This is the most common cause of a boiler failing to provide heat. If the gas jets on the burner will not ignite, no heat will warm up the water in the tank. The trouble may be due to a failed electronic igniter/pilot light, or perhaps trouble in the gas line.

How do you light a gas furnace with electronic ignition?

The pilot light has a separate small gas line running to it with its own valve. When the furnace comes on, this valve opens, and then the electric spark ignites the pilot. A flame sensor detects that the pilot is lit, opens the valve to the burners, and the pilot light ignites the burners.

How do you light a gas furnace with electronic ignition?

The pilot gas line is a small metal tube below the burner assembly and distinctive by the slight upturn at the end. It will be apparent, if the pilot is lit, by the small blue flame burning at the end. If you do not see a small blue flame burning, the pilot light is out.

Can you manually light a gas furnace with electronic ignition?

If your furnace is equipped with an electronic igniter, you cannot light the furnace manually. However, you may be able to get the furnace working by turning off the igniter and resetting it. Find the paperwork for your particular furnace to locate the reset button or switch.

How do you restart a gas furnace?

Once the gas has had time to dissipate, turn the knob to “Pilot.” Then, hold down the “Reset” button and bring the flame of a long lighter close to the pilot light opening. This should light the furnace pilot light. Once you are sure the pilot light is on, release your pressure on the reset button.

How do I know if my gas fireplace is working?

You should:
  1. Inspect the glass doors for cracks or latch issues.
  2. Check that gas logs are in the proper position.
  3. Turn gas off at the shut-off valve and test the igniter.
  4. Ignite the fire and look for clogged burner holes. If present, turn off gas and clear obstructions with a pin or needle.

Why does gas fireplace pilot go out?

If the pilot light on your gas fireplace won’t stay lit, a very likely culprit is a component called a thermocouple. The thermocouple is a metal rod that sticks out right in front of the pilot itself. It senses if flame is present or not. If the pilot light is lit, it heats up the thermocouple.

How do you reset a gas furnace?

Once the gas has had time to dissipate, turn the knob to “Pilot.” Then, hold down the “Reset” button and bring the flame of a long lighter close to the pilot light opening. This should light the furnace pilot light. Once you are sure the pilot light is on, release your pressure on the reset button.

How long can you leave gas fireplace on?

However, if your gas fireplace is vent-free or has doors on the front that can easily be opened, you should only operate it for two to three hours at a time, the service representatives said.

How much gas does a fireplace pilot light use?

Resetting a Gas Furnace
  1. Check to see if your pilot light is out.
  2. Turn down your thermostat as low as it can go.
  3. Turn off the power to the furnace.
  4. Turn off the main gas supply to the furnace.
  5. Light a match and hold it to the pilot flame jet’s opening, which is inside the furnace.