The sprinkler timer tells each valve to open at a specified time, run for a specified time, and then close. Some sprinkler timers can be connected to smart devices which automatically calculate when and how long the system should run and shut the system off when it is raining.

Similarly, How do you test Rainbird rain sensor?

For a cork-disc sensor:
  1. Locate the rain sensor for your irrigation system.
  2. Turn on the time clock for the zone nearest the sensor.
  3. Press and hold down the button on top of the sensor.
  4. Release the button and the zone should come back on.
  5. If the system does not shut off or come back on, check for wiring problems.

Also, How do I reset my Rainbird WiFi? Press the button on the LNK WiFi Module in the controller to activate AP Hotspot mode. The light should be blinking green and red. From your mobile device, go to WiFi settings and connect to the Rain Bird network β€œRAINBIRDXXXXXX”. Wait for your device to establish a WiFi connection with the LNK WiFi Module.


24 Related Questions and Answers Found πŸ’¬

 

Why does my Rainbird sprinkler system run twice?

A common reason why a program is repeating is that you have a second start time set. The start times control the exact time your ESP-Me timer will begin to water and they also control how many times a day your timer will water. The ESP-Me allows you to set up to 6 start times per program.

How do I reset my Rainbird controller password?

Press the settings icon (3 gears) on the bottom right corner of the controller screen. Press the down arrow for β€œController Info”. Press in the Controller Password field and change the password to something that will be remembered.

How do I reset my Rainbird sst600i?

Answer
  1. Turn the dial to Seasonal Adjust.
  2. Press and hold the left and right arrow buttons at the same time for at least 3 seconds. Until you see the word “CLEARED” on the screen.
  3. Turn the dial back to AUTO RUN. Your ESP-Me is now restored to the factory default settings.

What does no AC mean on a sprinkler system?

The “NO AC” display is a diagnostic message telling you that the controller has stopped receiving AC power. The controller is running on the power supplied by the backup battery. Check the power source by plugging a lamp or radio into the wall outlet to verify there is power at the outlet.

What does no AC mean on sprinkler system?

The “NO AC” display is a diagnostic message telling you that the controller has stopped receiving AC power. The controller is running on the power supplied by the backup battery. Check the power source by plugging a lamp or radio into the wall outlet to verify there is power at the outlet.

How do I reset my Rainbird controller password?

Press the settings icon (3 gears) on the bottom right corner of the controller screen. Press the down arrow for β€œController Info”. Press in the Controller Password field and change the password to something that will be remembered.

How do you replace a sprinkler solenoid?

You must replace the solenoid that resides on top of the underground valve.
  1. Turn off your water supply to the sprinkler system.
  2. Turn off your irrigation system at the control panel.
  3. Slide a soil probe into the ground to locate the failed solenoid and valve assembly.
  4. Scoop the soil off of the valve box using a shovel.

Why is my sprinkler system not turning off?

Turn off main water supply to sprinkler system after identifying the trouble valve. If there is debris or something inside the valve, carefully flush it out and put it back together again. Slowly turn the water supply back on and verify that the zone is now turning on and off properly both manually and electrically.

How do you winterize a Rainbird irrigation system?

How Do I “Winterize” My Irrigation System
  1. Insulate your assets: Shut off the water supply to the irrigation system.
  2. Stay in control: If you have an automatic system then you will need to “shut down” the controller (timer).
  3. Drain the pipes:
  4. Protect valves and backflow preventers:

How do I reset my orbit timer?

Reset to Factory Default – Orbit Irrigation B-hyve Help. To reset your timer back to factory settings: Turn the timer to the OFF position by rotating the dial. Open the front swing panel and press and hold the reset button for 10-12 seconds.

How does a Rain Bird Rain Sensor work?

Why does my irrigation system finish watering and then start again?

A common reason for a controller to repeat a cycle is too many programmed start times. When a station has completed its watering time, the controller will switch to the next station in that program automatically.

How does a Rain Bird Rain Sensor work?

How rain sensors work. The two leading manufacturers of irrigation products, Rain Bird and Hunter, both make rain sensors and both detect rain using the same method. They have a series of porous cork discs that when they get wet from rain, they expand and force the sensor to prevent the controller from watering.

How do I reset my hunter sprinkler timer?

X-Core
  1. Press and hold down the , and buttons.
  2. Press and release the RESET button on the right side of the controller.
  3. Wait 2 seconds and release the , and buttons. The display should now show 12:00am. All the memory has been cleared and the controller may now be reprogrammed.

How do you test a hunter sprinkler system?

To initiate the test program:
  1. Press and hold the PRG button. The station number will be flashing.
  2. Press the or button to scroll to the station you would like the test program to start with. Use the and buttons to set a run time of up to 15 minutes.
  3. After a 2 second pause, the test program will begin.

Why does my sprinkler system run twice?

A common reason for a controller to repeat a cycle is too many programmed start times. When a station has completed its watering time, the controller will switch to the next station in that program automatically.

Why does my sprinkler system keep running?

There are two reasons why your sprinklers would continue running: It’s possible your valves have been opened manually. You’ll need to locate your valve box(es) and turn the solenoid(s) clockwise until snug. The solenoid is located on the top of the valve and looks like a cylinder with two wires protruding out of it.

How do you test a hunter sprinkler system?

To initiate the test program:
  1. Press and hold the PRG button. The station number will be flashing.
  2. Press the or button to scroll to the station you would like the test program to start with. Use the and buttons to set a run time of up to 15 minutes.
  3. After a 2 second pause, the test program will begin.

How do I reset my orbit timer?

Reset to Factory Default – Orbit Irrigation B-hyve Help. To reset your timer back to factory settings: Turn the timer to the OFF position by rotating the dial. Open the front swing panel and press and hold the reset button for 10-12 seconds.