Fire Resistance

DensGlass Sheathing is noncombustible as described and tested in accordance with ASTM E136 or CAN/ULC S114. 5/8” (15.9 mm) DensGlass® Fireguard® Sheathing is included in a variety of UL and ULC listings and other designs in the GA-600 Fire Resistance Design Manual.

Then, Can DensGlass get wet?

DensGlass Sheathing is resistant to normal weather conditions, but it is not intended for immersion in water. Cascading roof/floor water should be directed away from the sheathing until appropriate drainage is installed. Avoid any condition that will create moisture in the air and condensation on DensGlass Sheathing.

Considering this, How do you cut a DensShield tile backer? Cut panel to required size and make cutouts. Fit ends and edges closely. Do not leave gaps between panels. DensShield Tile Backer may be cut by using a utility knife to score, then snap, working from the grey face side.


33 Related Questions and Answers Found 💬

 

What is DensShield drywall?

DensShield is an ideal tile backer board for high moisture areas because. it has a built-in moisture barrier that stops moisture at the surface. This special coating. helps protect the tile installation and wall cavity from moisture intrusion.

How much does a sheet of DensGlass cost?

Drywall Sheets
Everyday Low Price $19.99
11% Mail-In Rebate Good Through 2/29/20 $2.20

Can you finish DensGlass?

Panels are applied directly to structural framing. Surface and joints may be finished and painted, or surfaced with an exterior finish system. DensGlass Sheathing is resistant to normal weather conditions, but it is not intended for immersion in water.

What is Densboard?

DensShield® Tile Backer

The first backer board with a built-in moisture barrier. Engineered to prevent damage to the sub-floor or wall cavity if moisture seeps through grouted tile, DensShield® Tile Backer is the first backer board with a built-in moisture barrier.

Is DensGlass a vapor barrier?

Sto VaporSeal™ is an air and vapor barrier. It is a ready-mixed, flexible, waterproof coating which can be used on gypsum, cement or wood based sheathing substrates. Sto VaporSeal over DensGlass panels can be used on vertical above grade walls.

Can you paint over DensShield?

The nontiled areas can be primed and painted with the same finish used on the other walls in the room as long as the primer and paint are suitable for high-moisture areas.

What is dent shield?

Ding ShieldDent Protection and More

Being protected against everyday occurrences—such as run-away shopping carts, flying rocks or vertical curbs waiting to scuff your wheels—is one of the best ways to invest in the appearance of your vehicle and keep it looking as good as new and help retain its value.

How do you install a Diamondback tile backer?

twelve months

What is the best backer for tile?

Cement board is a good, reliable backer board that works well on both floors and walls. Keep in mind that most tile setters err on the side of caution and brush a waterproofing membrane on top of cement board when it is in wet areas like showers or tub surrounds.

What is cement board used for?

Cement backer board is mainly used as a sub-surface for tiling. Cement backer board is often used as a tile base on plywood or OSB subfloor. Cement backer board on concrete as a subfloor or underlayment is usually not recommended or needed.

Does cement board wick water?

If you use cement backer board, you have to install a separate moisture barrier between the board and any wood it’s attached to. Since the concrete can absorb and wick moisture, the barrier prevents wood rot if the backer board gets saturated with water.

What is gypsum backer board?

Water-resistant gypsum backing board (see ASTM C 1396, Standard Specification for Gypsum Board) is designed to be used as a base for the appli- cation of ceramic or plastic wall tile or plastic fin- ished wall panels in wet areas.

What is the best cement board for shower walls?

What is the best cement board for shower walls?

Tile Backer Board Breakdown
  • Foam boards are lightweight, easy to cut, and a completely waterproof. Pictured: Wedi Board tile backer board.
  • Schluter approves Kerdi over drywall.
  • Hardibacker is the best known fiber cement board.
  • Cement board has improved over the years and is easier to work with.

Can DensShield be used outside?

DensShield Tile Backer should not be used in commercial saunas, steam rooms, around fireplaces or areas where prolonged exposure to heat exceeds 125° F (52° C). DensShield Tile Backer panels should not be used as a shower pan base. DensShield Tile Backer should not be used for exterior installations.

What is DensGlass?

Widely recognized by the GOLD color, DensGlass® fiberglass mat gypsum sheathing has an exemplary track record that spans more than 30 years. It is a preferred substrate under brick, stone, stucco, siding and EIFS due to its ability to protect a structure against incidental moisture during and after construction.

What kind of screws do you use with DensShield?

No special or unique fasteners are required to fasten DensShield Tile Backer panels in place. For wood studs: galvanized roofing nails, rust-resistant drywall screws or bugle head deck screws. Fasteners should be long enough to penetrate at least 3⁄49 (19 mm) into the wood framing members.

What is the best material to use for shower walls?

What is the best material to use for shower walls?
  1. Glass Tile. Glass tiles are exactly what they sound like, they are translucent tiles that give an extra shine to your bathroom.
  2. Stone Tile. Stone tile is tiling that looks like a natural marbling.
  3. Ceramic.
  4. Acrylic.

Do I need to waterproof DensShield?

Showers with curbs— apply waterproof membrane up the walls a minimum of 29 (51 mm) and a maximum of 49 (102 mm) above curb. Showers without curbs — apply waterproof membrane up the walls a minimum of 69 (152 mm) and a maximum of 89 (203 mm). DensShield Tile Backer panels should not be used in shower curbs.

How do you install a Diamondback tile backer?

Water-resistant gypsum backing board (see ASTM C 1396, Standard Specification for Gypsum Board) is designed to be used as a base for the appli- cation of ceramic or plastic wall tile or plastic fin- ished wall panels in wet areas.

How do you tile a shower?

Contrary to popular belief, ceramic tile and grout, by themselves are not waterproof. Water can penetrate through cement-based grout and work its way through the substrate. To prevent water damage, you must install a waterproof membrane just below the tile bonding mortar as close to the tile as possible.

Is tile backer board fireproof?

Yes, HardieBacker® 1/4″ Cement Board is deemed noncombustible when tested to ASTM E 136 and can be used in conjunction with other noncombustible materials around a fireplace. This does not mean that clearances to combustible building materials can be reduced by using HardieBacker 1/4″.

What is DensShield made of?

DensShield Tile Backer is composed of a water-resistant treated core that is covered front and back with fiberglass mats. The mats are permanently integrated with the core during manufacturing, preventing delamination problems that can occur with paper- faced greenboard.

What is DensShield made of?

Apply clean, dry Diamondback Tile Backer to the base with the textured side facing out prior to the leveling material setting up. Fasten panel every 6” (150 mm) o.c in both directions, using 1-1/4” (32 mm) galvanized roofing nails or 1-1/4” (32 mm) corrosion-resistant backerboard screws.

Can you paint over DensShield?

The nontiled areas can be primed and painted with the same finish used on the other walls in the room as long as the primer and paint are suitable for high-moisture areas.

Do I need to waterproof shower walls before tiling?

Prepping for shower tile is different than the prepping for tile on drywall. A shower is considered a wet application, so you need to waterproof the foundation, which you’ll learn how to do in these instructions. After the waterproofing step, the instructions are the same as if you were installing tile on drywall.

Is DensGlass waterproof?

DensGlass Sheathing is the ideal substrate for a wide variety of air and water-resistive barriers including building wraps, fluid applied coatings, self-adhering membranes and spray foam applications. See page 10 for details. DensGlass Sheathing is lightweight and easy to handle.

What is DensGlass used for?

Widely recognized by the GOLD color, DensGlass® fiberglass mat gypsum sheathing has an exemplary track record that spans more than 30 years. It is a preferred substrate under brick, stone, stucco, siding and EIFS due to its ability to protect a structure against incidental moisture during and after construction.

Can you tile over waterproof membrane?

Prepping for shower tile is different than the prepping for tile on drywall. A shower is considered a wet application, so you need to waterproof the foundation, which you’ll learn how to do in these instructions. After the waterproofing step, the instructions are the same as if you were installing tile on drywall.

What is Red Guard waterproofing?

RedGard® is a liquid-applied elastomeric waterproofing material that cures to form a monolithic membrane. Benefits of Product in the Installation. Easy to use and can be applied by roller, trowel or airless sprayer. Rated for extra heavy duty service. Reduces curing time with quick-dry formula.

How do you install backer board in a shower?

Contrary to popular belief, ceramic tile and grout, by themselves are not waterproof. Water can penetrate through cement-based grout and work its way through the substrate. To prevent water damage, you must install a waterproof membrane just below the tile bonding mortar as close to the tile as possible.