Trim is seldom more than 4 inches, so you’ve got plenty of wiggle room with a 10-inch miter saw. A 10-inch blade will spin faster than a 12-inch blade, resulting in smoother cuts. Equal motors powering the two blades will result in a higher RPM rate on the 10-inch blade and higher RPMs mean a finer finish.

Hereof, Is festool Kapex worth the money?

Yes, it’s the best miter saw you can get (short of some specialized tools costing even more) but as a first Festool, the money is probably better spent elsewhere if you have other needs in your shop. I say this as a very happy Kapex owner. The Kapex, IMO, is the least distinguished of the Festool lineup.

Do you push or pull a sliding miter saw? A: Sliding miter saws are designed to cut on the push stroke. Pulling a miter saw through the cut results in a climb cut that could cause the blade to rise up out of the wood and chase after you. Also, it is important to use a blade with teeth that angle forward between 0Β° and 5Β°.


26 Related Questions Answers Found

 

Is more teeth on a saw blade better?

Blades with more teeth yield a smoother cut. Blades with fewer teeth remove material faster, but tend to produce a rougher cut with more β€œtearout”. More teeth means you will need to use a slower feed rate. No matter what type of saw blade you use, you will likely wind up with residue on the saw blade.

How do you cut a 60 degree angle on a miter saw?

The miter saw head can swivel for miter cuts, and the miter saw table can tilt for bevel cuts. However, a typical miter saw cannot cut a 60degree angle. You can solve this problem by adding a wedge block (jig) to the fence in order to attain a 60degree angle cut.

What is the difference between a miter saw and a chop saw?

The main difference between a chop saw and a miter saw is that a miter saw can rotate and produce angled cuts (or ‘miters‘ … hence the name). Chop saws only cut straight, 90-degree angles. Most often used with abrasive metal cut-off wheels, chop saws are hardy machines that will cut through just about anything.

Is more teeth on a circular saw blade better?

The rule of thumb is that a saw blade with more teeth means a smoother cut and fewer teeth means a faster cut. There are other things that affect the cut quality and the feed speed, like how fast you feed the material into the saw blade and how fast the saw blade is turning.

How big of a board can a 10 sliding miter saw cut?

A saw with a 10-inch blade makes right-angle cuts across a board 5 1/2 inches wide, sufficient for two-by-six lumber. The same 10-inch saw will cut a two-by-four at a 45-degree angle. Manufacturers also make 12-inch versions, which have a maximum cut of about 7 1/2 inches, wide enough for two-by-eights.

How many teeth should my table saw blade have?

For pipping solid wood: Use a 24-tooth to 30-tooth blade. You can use 40-tooth to 50-tooth multipurpose blade as well, but it will take longer. For cross-cutting wood or sawing plywood: Use a 40-tooth to 80-tooth blade. You can use a 40-tooth to 50-tooth general purpose blade as well.

What should I look for in a miter saw?

Blade size is an important consideration in selecting a miter saw. The most common miter saw sizes are 8, 10 and 12 inches. Keep in mind that larger diameter blades can make longer cuts. Positive stops are factory set points that let you quickly make precise cuts on specific angles.

How do you cut a 22.5 degree angle on a miter saw?

Are table saw and miter saw blades the same?

On the blade itself (the brand is Samona), it says “Mitre Saw Blade“, and the Table Saw can take 10″ blades, so will it work? The short answer is yes you can, but that’s a lot of teeth for a table saw blade.

Do I really need a sliding miter saw?

Because the saw head slides out on rails, it can’t offer the arc range a non-slider can – the head bumps into the rails. If you want to cut extreme angles, a slider isn’t the best choice. And it will come as no surprise that a sliding miter saw will almost certainly cost more than a non-sliding one.

What is the difference between a chop saw and a miter saw?

Chop saws are really powerful and are most often used in metal cutting. They have a larger motor and bigger blade than a miter saw and can cut through wood as well as large sheets or thick pieces of metal. The major difference between a chop saw and a miter saw is that chop saws are only able to make 90-degree cuts.

What is the difference between a 10 inch and 12 inch miter saw?

The 10inch miter saw has a smaller radius than the 12inch one, and this means that it tends to spin faster than the latter. A top quality 10inch saw will spin at about 5000 RPM while most 12inch ones can only manage a maximum of 4000 RPM. The quick turn of this saw means that it will make smoother cuts.

Do I need a sliding Mitre saw?

Because the saw head slides out on rails, it can’t offer the arc range a non-slider can – the head bumps into the rails. If you want to cut extreme angles, a slider isn’t the best choice. And it will come as no surprise that a sliding miter saw will almost certainly cost more than a non-sliding one.

How do you cut a 60 degree angle on a miter saw?

The miter saw head can swivel for miter cuts, and the miter saw table can tilt for bevel cuts. However, a typical miter saw cannot cut a 60degree angle. You can solve this problem by adding a wedge block (jig) to the fence in order to attain a 60degree angle cut.

What is the most accurate Mitre saw?

To calculate the proper miter angle for trim-work moldings, simply divide this angle reading by 2. In the example shown, the inside corner is 90.5 degreesβ€”nearly square. The precise miter angle of your moldings should be 45.25 degrees.

What is the most accurate Mitre saw?

Rotate the saw clockwise and set the miter angle at 31.6 degrees. Tilt the saw to the left and set the bevel angle at 33.9 degrees, if you haven’t already set it. Slide the molding to the right side of the blade to cut the left-hand piece for an outside corner. Turn on the saw and make the cut.

Are einhell Mitre saws any good?

This is the bigger and more powerful mitre saw offered by Einhell. It boasts a great range of features including double bevel angles and a sliding mechanism that makes it great for cutting wide planks. For a more in depth review and detail on the features click here for our Einhell TC SM 2131 240 Volt review.

Is festool Kapex worth the money?

Yes, it’s the best miter saw you can get (short of some specialized tools costing even more) but as a first Festool, the money is probably better spent elsewhere if you have other needs in your shop. I say this as a very happy Kapex owner. The Kapex, IMO, is the least distinguished of the Festool lineup.

How do you cut a 22.5 degree angle on a miter saw?

Cutting a 22.5 Degree angle on a miter saw

You must cut each piece of wood at an angle of 22.5 degrees to join two pieces of molding or baseboard at an angle of 45 degrees.

How do you lift a miter saw?

To unlock the blade’s side-to-side swivel action, you have to twist the knurled knob. If you loosen the knob, the miter saw will become unlocked and if you tighten it, then it will be locked in place. You can release the preset angle lock by depressing the lever using the middle or index finger.

Will a 10 miter saw cut a 4×4?

Miter Saws

Miter saw use teeth with blades to cut angles. It can do the 90-degree cut as a chop saw, but it can also do angles, bevels, and compound cuts at all different slants. If you’re making picture frames, trimming out doors and windows, or putting in moldings, a miter saw will be a lifesaver.

How do you cut more than 45 degrees on a circular saw?

How to cut more than 45 degrees with a circular saw
  1. Subtract the desired angle from 90 and cut that in the opposite direction. In our case, that angle would be 30 degrees.
  2. Make a 90 degree cut along the edge of the bevel. Now that we have out first beveled cut, we can set our circular saw back to zero to make a 2nd, 90 degree cut.

What is the difference between dws779 and dws780?

There is not quite difference in this aspect, but there is one feature that must be taken into account. The DWS779 model only comes with the steel blade, while the DWS780 also includes a carbide blade. This is a blade built in tungsten carbide, a chemical compound that contains tungsten and carbon.

What is the difference between dws779 and dws780?

5 Best Miter Saws 2020 – Our Reviews:
  1. DEWALT DWS780 12-inch Sliding Compound Miter Saw – Best Overall. Check Latest Price on Amazon.
  2. Makita LS1016L 10-inch Sliding Compound Mitre Saw.
  3. DEWALT DW715 Compound Miter Saw – Best Value.
  4. Hitachi C10FCE2 Compound Miter-Saw.
  5. Black+Decker Compound M1850BD Mitre Saw.

Should I buy a table saw or miter saw?

When it comes to this face-off, should you buy a table saw or a miter saw? A table saw can make longer cuts, while a miter saw excels in making short, beveled and angled cuts. A Table saw can make those same cuts if you have a jig, but it is more cumbersome.

Can you rip with a miter saw?

You can‘t use a rip blade for on a miter saw because the design of a miter saw is such that wood lays across its blade path and not along it. For this reason, you will not use a miter saw for ripping. Miter saws are powerful tools because they transcend regular carpentry jobs like cutting two-by-fours.

Do I need a compound miter saw?

Compound Miter Saws – These saws will cut at a variety of angles but also tilt in one direction (left) to cut a bevel. That’s useful when you need to cut at two different angles, such as when installing crown molding. Because the blade can move, it can cut wider pieces of wood.

How big of a board can a 10 sliding miter saw cut?

A saw with a 10-inch blade makes right-angle cuts across a board 5 1/2 inches wide, sufficient for two-by-six lumber. The same 10-inch saw will cut a two-by-four at a 45-degree angle. Manufacturers also make 12-inch versions, which have a maximum cut of about 7 1/2 inches, wide enough for two-by-eights.

Can a miter saw be used as a chop saw?

You can‘t use a rip blade for on a miter saw because the design of a miter saw is such that wood lays across its blade path and not along it. For this reason, you will not use a miter saw for ripping. Miter saws are powerful tools because they transcend regular carpentry jobs like cutting two-by-fours.

Should I buy a table saw or miter saw?

When it comes to this face-off, should you buy a table saw or a miter saw? A table saw can make longer cuts, while a miter saw excels in making short, beveled and angled cuts. A Table saw can make those same cuts if you have a jig, but it is more cumbersome.

Can I use a miter saw as a chop saw?

Miter Saws

Miter saw use teeth with blades to cut angles. It can do the 90-degree cut as a chop saw, but it can also do angles, bevels, and compound cuts at all different slants. If you’re making picture frames, trimming out doors and windows, or putting in moldings, a miter saw will be a lifesaver.