AF or F4E3. Restricted air flow. It indicates that the lint screen or vent is clogged; the vent is crushed, kinked or has too many turns. The dryer will continue to run when the is error is present. Touch any key to clear the code from the display and return to the estimated time remaining.

Then, How do you clean the lint out of a Whirlpool Cabrio dryer?

To clean inside the dryer, unplug it and turn off the gas, then open either the top or the front. The procedure is the same for gas and electric dryers. For dryers with a top lint filter and a solid front panel, remove the lint filter and take out the two screws on the side of the lint filter opening.

Considering this, What is AF on Maytag dryer? An AF (Restricted Air Flow) error code indicates that the lint screen or house vent is clogged; the vent may be crushed, kinked or have too many turns. The dryer will continue to run when the is error is present. Touch any key to clear the code from the display and return to the estimated time remaining.


33 Related Questions and Answers Found 💬

 

What does sensing mean on a Whirlpool Cabrio dryer?

One of the features of the Duet series of dryers is automatic dryness sensing. All Whirlpool Duet dryers have sensor strips in the drum. As your load of laundry tumbles in the drum, it makes contact with the sensor strips so that the dryer can end the cycle when your laundry is dry.

What does PF mean on a Whirlpool Cabrio dryer?

power failure

What does AF mean on a Whirlpool Cabrio dryer?

AF or F4E3. Restricted air flow. It indicates that the lint screen or vent is clogged; the vent is crushed, kinked or has too many turns. The dryer will continue to run when the is error is present.

Why is my Cabrio dryer squeaking?

If your dryer is making a squeak, squeal or ear piercing noise, it’s highly likely you need to replace your idler pulley . This is a very common issue and very easy to fix. Most dryers, you’ll remove the front of the dryer, have to take out the drum and do a whole bunch of other stuff to get to the idler pulley.

How do I reset my Whirlpool Cabrio dryer?

How to Reset a Whirlpool Cabrio
  1. Touch any key on the display pad to clear the error code, if applicable, or press “Pause/Cancel.”
  2. Choose a new cycle and press “Start” to begin.
  3. Turn off and disconnect the Cabrio if the error or problem persists.
  4. Wait several minutes before restoring power.
  5. Contact Whirlpool for assistance if the unit will not reset.

What is wrong with my dryer it wont turn on?

If your dryer won’t start, the most likely causes are a lack of power, a defective door switch, a blown thermal fuse or a bad start switch. Open the dryer door and check if the light inside the dryer turns on. If it doesn’t turn on, check your power cord and the house circuit breaker.

How do I fix the l2 code on my Maytag dryer?

Replace the dryer fuse(s) or turn off the household circuit breaker for the dryer for one (1) minute, to reset the circuit breaker, then turn on the circuit breaker. Confirm that the power cord is properly installed. Refer the Installation Instructions for details. Select a Timed Dry heated cycle and restart the dryer.

How do I reset my Kenmore Elite Smartwash quiet Pak 9?

Touch the left multimeter lead to the left side of the thermal fuse; touch the right multimeter lead to the right side of the fuse. Keep an eye on the multimeter needle; a needle that fails to move indicates a blown thermal fuse. If this is the case, don’t fret: thermal fuse replacement is a simple task.

What does check lint screen mean?

The control panel has an indicator light “Check Lint” or “Check Lint Screen” to remind you to clean the lint screen before each load. It is normal for the light to be on or flashing before the cycle starts. The indicator light will turn off once the door is opened or a cycle is started.

How do you diagnose a dryer problem?

Problem: Dryer Won’t Start
  1. The door latch may not be engaging. Check the latch for lint and clean it completely so that the door closes properly.
  2. Check the power supply, including fuses and circuit breakers.
  3. Check the dryer’s internal thermal fuse.
  4. If you have a push start knob, it may not be engaging correctly.

What causes a dryer to not come on?

A thermal fuse is a heat-sensitive fuse attached to your dryer’s exhaust duct (in most models) that is designed to blow if the dryer overheats. A blown fuse would cause your dryer to not heat, or to not work at all. Open up your dryer’s cabinet and locate its thermal fuse.

Where is the thermal fuse on a Kenmore Elite Oasis dryer?

On the Kenmore site for my unit it said look for the fuse on the dryer vent. On your dryer, the thermal fuse is located on the exhaust blower housing. To access the thermal fuse you will need to disassemble the dryer.

How do I fix my Maytag dryer?

How do you clean the lint on a Whirlpool Cabrio Platinum dryer?

How to Clean Lint Out of a Whirlpool Dryer
  1. Grab the lint screen and pull it up and out of the lint catcher in either the door or the top of a Whirlpool dryer.
  2. Roll the lint from the lint screen with your fingers.
  3. Wet the screen with hot water.
  4. Rinse the screen and dry it thoroughly with a towel or allow the screen to air dry.

How do you fix the start button on a dryer?

Instructions
  1. Shut off the power. Unplug the dryer.
  2. Pull the knob off. Pull the control knob straight up and off of the front of the push-to-start switch.
  3. Remove the back panel.
  4. Remove the push-to-start switch.
  5. Install the new push-to-start switch.
  6. Reattach the back panel.
  7. Reinstall the control knob.
  8. Restore power to the dryer.

What does f40 mean?

The F40 error code indicates a communication failure between the main machine control board and the motor control board for the blower motor on the dryer. This can be caused by a loose wiring connection blown thermal fuse on the dryer, as well as a bad thermistor that is causing the dryer to overheat .

Can you reset a thermal fuse?

You can‘t reset the thermal fuse; if it’s blown, replace it with the manufacturer-approved replacement part.

What does F mean on my washer?

The F indicates that the washer control detected a component problem. Since the door remained locked, your likely problem was with the drain pump or excessive suds preventing the washer from draining out the water properly.

How do you reset a dryer fuse?

How to Reset a Thermal Fuse
  1. Unplug the clothes dryer’s power cord from the wall outlet.
  2. Swing the front panel out towards you so that you can look into the compartment.
  3. Aim a flashlight at the flat-can-like component to locate the blown thermal fuse.

How do I reset my Kenmore Elite Smartwash quiet Pak 9?

When a clothes dryer doesn’t heat the air but its drum rotates, something has interrupted the heat source. With an electric clothes dryer, no heat often means that the circuit breaker or fuse that controls the power has blown; reset or replace it. Be aware that a dryer may have two breakers or fuses.

Where is the reset button on a Kenmore Dryer?

What does f2 mean on a dryer?

F2 flashes when there is a stuck button or user interface mismatch. You can try performing a hard reset to fix the problem. Unplug or turn the circuit breaker off for 30 seconds.

Why is my Kenmore Elite washer not draining?

If the washer won’t drain there might be a clogged pump or hose. It’s common for small socks or other small clothing items to get into the water drain system and clog the hose leading to the pump or the pump itself. Cleaned the filter and the machine still will not drain. So that must mean the hose or pump is clogged.

Why is my Kenmore Elite washer not draining?

How to Reset a Kenmore HE4t
  1. Press and hold “Drain & Spin” for three seconds to release the child lock, if the keypad is locked.
  2. Press “Pause/Cancel” twice to cancel the current operation.
  3. Turn off and unplug the washing machine.
  4. Wait several minutes before restoring power to properly reset the machine.

How do you fix a dryer?

Replace the bad heating element on an electric dryer by unscrewing the retaining clip at the top of the heater box. Then pull out the box and remove the element retaining screw. Swap the elements and reinstall. If you have an electric or gas dryer that tumbles but won’t heat, check the thermal fuse for continuity.

Do all tumble dryers have a reset button?

In some models this should be easily fixable – some tumble dryers have reset buttons on the back of the machine so all you will need to do is hold in the button and wait for it to click.

Can I bypass the thermostat on my dryer?

The idea would be to bypass the thermostat, hi-limit or thermal cutoff one at a time and see if the dryer will heat. Then carefully plug the dryer in and run it to see if it will heat. If it heats the thermostat is the problem. If it doesn’t heat then the thermal cut-off and hi-limit can be checked the same way.

Can you run a dryer without a thermal fuse?