Check that condenser isn’t blocked with lint. The condenser should be cleaned once a month, the easiest way is to run water through the condenser. The machine will stop heating (The load may still be wet at the end of the drying cycle) the ‘ Empty water ‘ light should flash to tell you that the water container is full.

Similarly, How do you reset a Zanussi Lindo 300 dryer?

Press and hold the start button and the button to the left of it. Keep them both held in and turn the dryer back on. Keep the buttons held in for several seconds till the lights start to scroll then let go. Then once its done this turn it back off and on then off again.

Also, How long is Zanussi guarantee?

1 year

26 Related Questions and Answers Found 💬

 

Where is the filter on a lindo300?

The model number is generally found on a sticker on the inside of the door of your washing machine. It’s also possible it is on a sticker on the inside of the small door that covers the filter.

How do I fix e40 error on washing machine?

Resolution
  1. Check if the door/lid is properly closed. If necessary, give the door/lid a firm push.
  2. There is too much laundry in the machine (overload). If necessary, remove some laundry from the drum before restarting the cycle.
  3. Check the mechanical child safety lock (if applicable).
  4. Contact authorized Service Centre.

How do you bypass a washing machine door lock?

How to Bypass a Washing Machine Lid Lock
  1. Turn off the washer and unplug the appliance.
  2. Locate the retaining tabs and/or screws that hold the top horizontal panel down.
  3. Look for the lid lock switch on the underside of the top panel and where it fits into the appliance.
  4. Put the lid back down and plug the washing machine back into the electrical outlet.

Why is my Zanussi washing machine not draining?

Dirty filter:

If the drainage does not function properly, it may cause the machine not to spin. Clean the drain filter and the pump blade (if the pump blade is visible, turn it using a pencil and remove any fluff or foreign objects). Then refit the filter and start a hot wash without any soap to clean the machine.

What does e10 mean on washing machine?

Washing machine displays error message E10, E11, C1 or emits 1 beep / 1 flash. It indicates problem with not taking in water, not taken in enough water or problems with the drain.

How do I fix e40 error on washing machine?

Resolution
  1. Check if the door/lid is properly closed. If necessary, give the door/lid a firm push.
  2. There is too much laundry in the machine (overload). If necessary, remove some laundry from the drum before restarting the cycle.
  3. Check the mechanical child safety lock (if applicable).
  4. Contact authorized Service Centre.

How do clean a washing machine?

Add two cups of white cleaning vinegar to detergent dispenser. Run it through a complete cycle. Run another cycle on the highest level and at the hottest water temperature, this time adding one-half cup of baking soda to the drum. When cycle is done, wipe inside drum of washer with a damp microfiber cloth.

How do you check a dryer fuse?

E41 – This error code indicates your washing machine door is open so check it’s closed! Check the door lock if the error persists.

How do you troubleshoot a dryer?

Problem: Dryer Won’t Start
  1. The door latch may not be engaging. Check the latch for lint and clean it completely so that the door closes properly.
  2. Check the power supply, including fuses and circuit breakers.
  3. Check the dryer’s internal thermal fuse.
  4. If you have a push start knob, it may not be engaging correctly.

Why is my washing machine not working?

If your washer fills with water but doesn’t agitate, the problem is likely to be a faulty lid switch, a broken belt, or a problem with the motor. 1 Check the washing machine’s spin cycle. If this works, the motor is operating and the belt is not broken. If the spin cycle doesn’t work, the belt may be loose or broken.

Do Zanussi washing machines have filters?

There is no longer any filter that needs cleaning in the Zanussi washing machines. Coins, buttons, other small items forgotten in the pockets of your clothes are deposited during the washing cycle in the special double lip trap in the porthole seal, where they can be conveniently recovered at the end of the cycle.

What is wrong with a dryer when it doesn t get hot?

With an electric clothes dryer, no heat often means that the circuit breaker or fuse that controls the power has blown; reset or replace it. Be aware that a dryer may have two breakers or fuses. The motor will run when one works, but the heating element requires both.

How do you remove a Zanussi filter?

How does a washing machine door lock work?

When you shut the door, the latch on the door pushes inside the door lock onto a sliding bar which moves over and activates an electrical part inside which locks the door shut. At the same time, power is passed through the interlock on to the rest of the machine.

How do I fix e20 error on my washing machine?

Resolution:
  1. Ensure correct position of the drain hose.
  2. Ensure correct drain height.
  3. Clean the pump and filter.
  4. Check for blocked drain.
  5. Check the drainage hose for possible kink or twist.
  6. Use less soap powder.
  7. Switch off the power to the washing machine.
  8. Contact an Authorized Service Center.

Which is the best washing machine?

For us the best washing machine of all is still the AEG 9000 Series.

The best washing machines to buy, in order

  1. AEG 9000 Series L9FEC966R.
  2. Bosch Serie 6 i-Dos WAT286H0GB.
  3. LG F4V910WTS.
  4. Beko WTG1041B2.
  5. Samsung Ecobubble WW90J5456FC.

How do I fix my washing machine?

It’s an easy and inexpensive fix, about $22.
  1. Fix 2: Draining problems. Replace the pump. Tip the machine back and support it with blocks.
  2. Fix 3: Slow fill or no fill. Replace the water valve. Remove the water valve bracket and mount the new valve.
  3. Fix 4: Won’t agitate or spin. Replace the lid switch.

How do you reset a dryer fuse?

How to Reset a Thermal Fuse
  1. Unplug the clothes dryer’s power cord from the wall outlet.
  2. Swing the front panel out towards you so that you can look into the compartment.
  3. Aim a flashlight at the flat-can-like component to locate the blown thermal fuse.

How do you diagnose a washing machine?

Remove the power source to the washer before troubleshooting or attempting repairs.
  1. #1 – Washer Won’t Turn On.
  2. #2 – Not Draining Properly.
  3. #3 – Will Not Spin and/or Agitate.
  4. #4 – Washer Leaking Water.
  5. #5 – Does Not Dispense Detergent.
  6. #6 – Washer is Shaking and Moving.
  7. #7 – Washer is Noisy.
  8. #8 – Washer Smells.

How do you check a dryer fuse?

Zanussi produce quality home appliances that are built to last and which come with a 1 year manufaturer’s warranty as standard to protect against manufacturing faults and defects that occur during the first year.

Touch the left multimeter lead to the left side of the thermal fuse; touch the right multimeter lead to the right side of the fuse. Keep an eye on the multimeter needle; a needle that fails to move indicates a blown thermal fuse. If this is the case, don’t fret: thermal fuse replacement is a simple task.

Can you reset a thermal fuse?

You can‘t reset the thermal fuse; if it’s blown, replace it with the manufacturer-approved replacement part.

Why won’t my dryer start all of a sudden?

If the dryer won’t start the motor might be defective. Before replacing the motor, check the thermal fuse, start switch and door switch because all three are more likely the cause. However, in some dryers when the drive belt breaks the tension pulley arm trips a switch which shuts off power to the entire dryer.

Why won’t my dryer start all of a sudden?

How to Check a Dryer Thermal Fuse
  1. Unplug the dryer and remove the front access panel.
  2. Locate the blower cover–it’s the large object facing you at the bottom of the dryer.
  3. Remove the wires from the thermal fuse terminals to test it.
  4. Set your multimeter to the R x 1 scale and touch the leads to the thermal fuse terminals to test for continuity.

What would cause a dryer to not spin?

A broken drive belt is the most common reason a dryer won’t spin. To fix this issue, turn the drum by hand. A working belt should provide some resistance, so if the drum turns very easily and loosely, the belt is probably broken.

How do I reset my phone?

Factory reset your Android phone from the Settings menu
  1. In the Settings menu, find Backup & reset, then tap Factory data reset and Reset phone.
  2. You’ll be prompted to enter your passcode and then to Erase everything.
  3. Once that is done, select the option to reboot your phone.
  4. Then, you can restore your phone’s data.

Why is my washer not draining or spinning?

If the washer won’t drain there might be a clogged pump or hose. It’s common for small socks or other small clothing items to get into the water drain system and clog the hose leading to the pump or the pump itself. If the washer won’t drain the lid switch assembly might be defective. This is a very common problem.

How do clean a washing machine?

Add two cups of white cleaning vinegar to detergent dispenser. Run it through a complete cycle. Run another cycle on the highest level and at the hottest water temperature, this time adding one-half cup of baking soda to the drum. When cycle is done, wipe inside drum of washer with a damp microfiber cloth.

How do I know if my thermal fuse is blown?

Factory reset your Android phone from the Settings menu
  1. In the Settings menu, find Backup & reset, then tap Factory data reset and Reset phone.
  2. You’ll be prompted to enter your passcode and then to Erase everything.
  3. Once that is done, select the option to reboot your phone.
  4. Then, you can restore your phone’s data.

What does e30 mean on a Zanussi washing machine?

Washing machine displays error message E30, C3 or emits 3 beeps. The error is caused by water at the bottom or inside the machine.

Touch the left multimeter lead to the left side of the thermal fuse; touch the right multimeter lead to the right side of the fuse. Keep an eye on the multimeter needle; a needle that fails to move indicates a blown thermal fuse. If this is the case, don’t fret: thermal fuse replacement is a simple task.